Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Rikon 10" bandsaw

Posts

Rikon 10" bandsaw

#1

Rikon 10" bandsaw

Paul M.

I rarely post on this forum as I primarily hang out on the hand-tool forum. But I wanted to share a review on my new little powered toy.

I've had a Laguna 14SE bandsaw for many years. The lower saw guide on the Laguna is one of the stupidest designs I've ever seen and requires 3 hands and wrenches to adjust the lower guides to change blade sizes. As such, I've tried cutting curves with wide blades and tried resawing with narrow blades just because I don't want to fight those stupid bearings doing a blade change once again.

I saw the Highland Hardware sale on the Rikon 10-305 10" bandsaw for only $199. This sale has been going on for about the last 6 months. I finally bit and bought one. I figure when I want to cut curves and small items, a 1/4" blade with a small throat is just fine and I can keep the Laguna setup for a 3/4" resaw blade for the big stuff.

My first impressions are pretty good for this little saw. The table is cast iron, and the frame seems rigid enough to hold tension on a small 1/4" blade with no problems. The wheels are spoked steel and run true. The blade is supported with a thrust bearing (blade hits on the outside of the roller not across the face of the bearing) on both upper and lower, with side bearings on each support as well. This is a better setup than cool-blocks as far as I'm concerned. It also has a rack and pinion upper blade guard which is something I wish my Laguna had.

The "trunion" is completely a joke on this saw as I doubt this cast aluminum piece weighs more than an ounce or two. But I will keep this table at 90 degrees to the blade and it seems to lock the table at that setting.

The "fence" is also laughable. You could easily balance this on your pinky without any stress as it is so light. It's difficult to get it clamped down straight as there is so much play in it. But with a little concentration and pushing the fence tight to the rail as you lock it down does work.

The 2-1/2" dust collection is from a port below the lower wheel. It's fine for the small amount of dust that a 1/4" blade will make when cutting nothing bigger than 2" thick (my expected usage, not a tool limitation).

All in all, a good usage of $200 to keep me from fighting the blade changes on the Laguna. I would not make this cute thing my only bandsaw, but it will see lots of use in my small shop making guitar parts.

[Edit]: I forgot to mention a couple of other things associated with this saw:

Another good point: The upper and lower wheel guides can both be adjusted for proper tracking. This is a nice touch for a cheap saw. Most saws in this price range only have tracking on the upper wheel and not the lower.

Another bad point: There is no blade tension guage. These are usually a joke anyways on most cheap bandsaws, so I'll just pluck this and listen for a tone to tension.

Re: Rikon 10" bandsaw

#2

question?

bill tindall

As the blade travels over the wheel it flexes. There is a relationship between wheel diameter and blade thickness that must not be exceeded or the flexing will lead to shortened blade life- blades will break somewhere other than the weld. "I have heard" (as they say) that 14" is about the limit for wheel diameter for the typical blade thickness. Let us know how blades hold up on the small wheels.

Re: Rikon 10" bandsaw

#3

Re: question?

Paul M.

Hi Bill,

I've also heard that 14" is the smallest wheel size for blade life, but I seem to remember that was when referencing the lifespan of a quality resaw blade. The neuron that retains that piece of info is however probably faulty.

I'm not too worried about blade life on this tiny saw. It will only see 1/4" utility grade blades and they are only $16.00 from Highland Hardware. I bought a couple along with the saw as I figure they won't last forever.

I did have a Shopsmith bandsaw years ago and I think that one was also only 10". I never had any issues with blades breaking or having tracking issues on that saw either. The main wheel bearings went out on the Shopsmith bandsaw and made a heck of a noise even with no load on the blade so I unloaded that one. But it wasn't due to small wheel size.

Re: Rikon 10" bandsaw

#4

Re: question?

Jerry Gibbs

I used to have a 3 wheel bandsaw that had a 16" throat or so, but turned over small diameter wheels. Kept breaking blades so I used the stand and motor for something else. I have a 10" 2 wheel cheap bandsaw now that does not break blades.

Re: Rikon 10" bandsaw

#5

Re: Rikon 10" bandsaw

Andy Lincoln,in Dearborn MI

HI All,

As a note to others who may look to add a small band saw to the shop. I was experiencing similar circumstances as Paul was.Always having t he wrong blade on my JET 18" for what I wanted to do at the moment.I began searching for a small band saw for cutting curves and smaller parts. The Rikon from HH intrigued me as well and with a little shopping and research I concluded that the exact same saw is marketed by Sears as a Craftsman 10" band saw..same adjustments,castings,style ,etc.I would be willing to go out on a limb and say they are made in the same far east factory.The bonus to the Craftsman? Local availability and I caught a sale where it only cost $149 +tax.The local sears store is less than 5 miles away ,assembly was quick ,out of the box and seems to be a nice,small convenient saw.

Andy

Re: Rikon 10" bandsaw

#6

there are much cheaper places to buy blades

bill tindall

I get mine made at Misenheimer, Morristown, TN. I just bought several 141" x 1/4 to 3/4"blades for about $10 each. I suspect any saw shop that welds blades from bulk rolls would have similar prices. The blades are either Lenox or Sterrett.

Re: Rikon 10" bandsaw

#7

Re: Rikon 10" bandsaw

John Veerkamp

Paul,

I have the 14" Rikon and the tension "gauge" is inside the top cover on the top left. A needle pointing to the blade width. Not very accurate but a relative guide.

John

Re: Rikon 10" bandsaw

#8

Re: Rikon 10" bandsaw

Paul M.

Hi John,

They saved a buck and left the tension gauge off of the 10" version. No big loss as it can only run little blades anyways which are easier to tension by plucking a note on the blade.

Re: Rikon 10" bandsaw

#9

Re: Rikon 10" bandsaw

Paul M.

Thanks Andy. My friend is interested in getting his own copy of this cheap little toy. I'll let him know that Craftsman has a similar saw.