Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

OT - is treated plywood overkill in this job?

Posts

OT - is treated plywood overkill in this job?

#1

OT - is treated plywood overkill in this job?

Bill Houghton, Sebastopol, CA

Situation: concrete slab, 6-12" of slab exposed above grade, resting on 4" of gravel and a sheet of plastic. I'm putting down a plastic vapor barrier and screwing down 1/2" plywood (all of this to get a little elevation for drainage where the door abuts on a brick patio). Screwholes will get a shot of poly caulk before the tapcons are driven. All of this inside an enclosed space.

Space will be used as a studio with occasional overnight guests. A floating laminate floor will go on top of the plywood, over the usual thin foam underlayment.

I was planning to put down treated plywood, but am wondering if this is overkill. I realized today that, if I trust the vapor barrier at all, it should be enough that regular CDX ply would be fine, with less outgassing of fumey junk in the occupied space.

Help!

Re: OT - is treated plywood overkill in this job?

#2

Re: OT - is treated plywood overkill in this job?

Barry Irby

Check With your local Code authority. I am nearly certain that the code requires treated wood if it is in contact with concrete on grade. With or without a vapor barrier.

It might be successful to go without the treated wood, but the foam pad for the laminated floor is a vapor barrier and you would have the untreated plywood trapped between it and the one in the concrete. Hard to predict what the moisture level would be. A few years down the road you might discover it rotted.

Why put the plywood down at all? Couldn't you just install the laminate over the slab?

Unless the door is very well protected and never gets wet you should install a sill flashing. Check out Jamsill Guard.

Re: OT - is treated plywood overkill in this job?

#3

Jason Roehl in Lafayette, IN

I think Barry's on to something...

Jason Roehl in Lafayette, IN

...in that you would likely have some moisture problems down the road trapping the plywood between two vapor barriers. What would be a whole lot better is to have whatever thickness of lightweight concrete poured on top of the slab to help you gain the height, then lay the foam and laminate directly on top of the lightweight.

Jason

Re: OT - is treated plywood overkill in this job?

#4

Self-leveling compound?

Bill Houghton, Sebastopol, CA

I followed up on Jason's suggestion. Lightweight concrete doesn't seem likely - too costly for what is about 4 cubic feet.

Self-leveling compound, with pea gravel to extend it, seems like a prospect. In reading the literature, it looks like this sets up pretty fast - I'm wondering how easy it would be to screed the compound and pea gravel to 1/2" thick accurately in the time I have before it sets up.

Thoughts from any tilesetters in the room appreciated.

Re: OT - is treated plywood overkill in this job?

#5

Jason Roehl in Lafayette, IN

In that case...

Jason Roehl in Lafayette, IN

Perhaps you could bed cement board (Durock and the like) in thinset like you were laying tile, then use mesh tape (the gray stuff for this purpose) and thinset on all the seams on the top side. Use a 1/4" notched trowel for the thinset, then 3/8" or 1/2" cement board. Quick, uniform thickness and water resistance all in one.

Then you could lay your foam and laminate on top of that.

Jason

Re: OT - is treated plywood overkill in this job?

#6

Maybe fiber re-inforced concrete?

John in NM

I think I'd look into making something similar that has a long enough working time for your needs (I'm assuming from the context that the leveling stuff sets up quick). I'd look into admixtures for mortar and stucco that will increase tensile strength, such as chopped fiber or the white stuff everyone seems to call either "milk" or "glue" (an EVA I understand, but thinner than elmers). The advantage of mixing your own is that you can skip adding the various accelerating compounds if you need working time. You might need a mixer for 4' though.

The downside is that the stuff is going to crack :D

There's three rules of concrete.

Its grey

It gets hard

It cracks

With any luck, chopped fiber might keep the cracks small, and the milk might help it stick to the existing pad.

Re: OT - is treated plywood overkill in this job?

#7

I like Jason's idea better than mine!

John in NM

That should work fine :D

Not sure it will be any more water resistant than concrete unless the thinset is designed not to wick. But your foam will be a moisture barrier, so no worries there.

Re: OT - is treated plywood overkill in this job?

#8

Re: Self-leveling compound?

FredD

Bill,

for the small area you describe , FixAll, readily available out there at all hardware stores and from small cans to fifty pound bags is far and away the best, easiest and fastest leveling compound.

It dries fast and very hard , so you will want to straight edge with a Darby float or trowel right to the final finish without any sanding.

FredD