Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Replacement bearing for router bit??

Posts

Replacement bearing for router bit??

#1

Replacement bearing for router bit??

Barry Irby

I have a half inch router bit with a half inch bearing on the lower end. (I can 't remember whether that makes it a flush trim or pattern bit.) I also have no idea what brand it is or where I bought it. It has a nut on the bottom and that comes off easily as well as the bearing.

The problem is the bearing failed and coughed up what look like BB's. So, Where does one find replacement bearings?

Re: Replacement bearing for router bit??

#2

Re: Replacement bearing for router bit??

Carol Reed, Strawberry, AZ

You need a high speed bearing. Steer clear of bearing shops. They typically don't carry anything with a rating over 8,000 RPM. Routers go 3 1/2 times faster. Check with router bit suppliers. They will carry the router bearings. And yes, they run 3 times as much money as the "slower" bearings. Such is life.

Re: Replacement bearing for router bit??

#3

Re: Replacement bearing for router bit??

David Yoho

Barry, I would imagine if you provided the exact specs (I.D., O.D., thickness), most any router bit outfit should be able to sell you one. Although, if it were me, I think I'd just buy a whole new bit. Yours sounds like a flush-trim. To add to that, if I were to buy a new one, I'd look for a half-inch spiral flush-trim. They cut smoother than the straight ones do.

David

Re: Replacement bearing for router bit??

#4

Clint Searl

Excellent advice

Clint Searl

Router bits are consumables. A dead bearing implies a dead bit.

Clint

Re: Replacement bearing for router bit??

#5

Re: Excellent advice

Gary Smyth

Contact Ridge Carbide Tool Company, Router Bits.com, Infinity Cutting Tools, Porter Cable Router bits, and Freud sells them too. Make sure the screw and bearing permit rotation. I use Bostik bearing lubricant spray once you get what you want. It burns off quickly, but it does the job so far. If you want to continue use of the bit, use it as a straight bit w/o the bearing and get a new spiral flush cutter. You'll feel better and not worry about matching the bearing size.

Re: Replacement bearing for router bit??

#6

Do You Have A Rabbeting Set?

George Colonel's Workshop-Havertown PA

Good Morning Barry,

While I do agree that a spiral bit is superior I wouldn't necessarily discard a perfectly good bit if a replacement bearing was available. Catalogs such as Eagle America and Woodline sell replacement bits which are inexpensive. I'd go there first. In the meantime, should you need to use your bit, you may find the correct size bearing in a rabbeting set if you have one. I recall having a large bearing seize on a CMT stacked Cope and Stick combination, and a new bearing saved me considerable money.

George

Re: Replacement bearing for router bit??

#7

Look for a number on the seal...

John in NM

Then look here:

http://www.vxb.com/

They list router bearings by inside diameter.

Only trouble is you may pay more for shipping than the bearing :D

Most large cities will have several bearing suppliers, google bearing supplier and the city. You'll pay more than on the internet, but won't have to pay shipping, so its a wash.

Re: Replacement bearing for router bit??

#8

Re: caveat about bearing suppliers

Carol Reed, Strawberry, AZ

If you go that route, be certain to explain your application. This is how I learned about high speed bearings. My experience is that they have so little call for them, they have to order them for you and THAT will cost you more money - plus shipping.

Cheapest, easiest is to go to the router bit supplier. Half inch OD bearings that will fit several of your bits are good to have an extra on hand. So get two.

However, do consider that if the bearing is trashed the bit may well be also.

Re: Replacement bearing for router bit??

#9

Re: Do You Have A Rabbeting Set?

Barry Irby

Thanks, Good idea.

I am suffering from frugality and the "I can fix this syndrome." My rational brain knows it's probably better to by a new spiral bit and this is a good excuse to do just that. But then my grand mother would be spinning in her grave. I can hear her saying, "you don't need a whole new one, you can fix the one you have."

I was surprised at the quality of the bearings. I found three of them on the shop floor and though they were BBs. Sort of crappy looking for high speed bearings.

Re: Replacement bearing for router bit??

#10

Thanks, John and Carol

Barry Irby

The seal is long gone. this bearing did not just seize up, it dismantled itself and flew away in pieces. I knew it was ruined and was working on a rough project and dogged it completely to death. This is a half inch bit with a half inch bearing, so it was pretty small and light weight.

I think I will find a spiral bit with a bearing and buy a larger one to allow for a more substantial bearing. and I may also fix the existing bit if I can find a suitable bearing so I can have two flush cutting bits.

Thanks for the warning on the quality of the bearings.

Re: Replacement bearing for router bit??

#11

Re: Replacement bearing for router bit??

Dave Bair, Eaton Rapids, MI

Try MLCS (mlcswoodworking.com); the offer free shipping and carry standard replacement bearings.

Re: Replacement bearing for router bit??

#13

Re: Do You Have A Rabbeting Set?

Phil Joines

"Sort of crappy looking for high speed bearings. " They probably looked much better when they were new :>)

At my last job they did a lot of pattern routing. It was common for the bearings to go out when the bit was still good. They weren't interested in replacing the bearings, just tossed them all.