Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

How To??

Posts

How To??

#1

How To??

Mark Mandell - Gone Round In Jersey

Friend handed me a set of side rails to a K-D bunk bed, the kind with those steel double hooks on the ends with the stopped steel pegs, for repair; the rail being split along most of its length.

Wood is maple and I could make a new sideboard easily enough, but I have no clue as to how the slots for the hook thingies are cut into the ends.

Anybody done this, chime in here, please.

Re: How To??

#2

Re: How To??

George Colonel's Workshop-Havertown PA

Good Afternoon Mark,

I used my bandsaw, and several steady handed kids to keep the rail level and true. Getting the right kerf width was adventuresome, but doable. As I recall, I used a 3/4" Timberwold resaw blade and a home-made fence on my 14" Jet Bandsaw.

George

Re: How To??

#3

Re: How To??

Grant in Iowa

I made a bed with those hooks. Here is how I cut them:

I tipped my Radial armed saw so the arbor was perpendicular to the table. I added an auxilliary table such that the blade could be brought into alignment with the desired cut line on the end of the bed part. I locked all movement on the saw arm.

I made a robust fenced table on the right side of my saw so the blade was rotating TOWARDS the fence, thereby preventing the workpiece from being pushed away from the fence. Atop this fenced table I laid the part. I set up stop blocks so I couldn't cut too deep. I installed a ripping blade of the right diameter and thickness into the saw.

When I was sure I would have no movement of the part except left to right, I slowly fed the part into the blade. After careful preparation, the cuts went very well.

The key is to control your cut and feed slowly. I should add that I needed to adjust the setup for two of the cuts, since they were mirror edge versions of the first two cuts.

While that worked for me, several folks here expressed concern at the time about the safety of the cut (though I am not sure exactly why). Apparently any time you use a radial arm saw, somebody cries unsafe.

So, in the interest of appeasing those folks, I offer another solution. You could also make a jig to hold a circular saw at the right point on the end of one of these boards. Again, control everything except the plunge portion of the cut, then make your cut. You could also actually clamp the base of the circular saw to the jig for added safety. This same jig could also be used to make appropriate cuts in the bedposts.

You will also find that a certain diameter and width of blade will make the proper cut possible in just a plunging motion. Too small a blade and you will need some forward motion as well, too large and it will not cut deep enough without emerging from the sides of your part. If I remember correctly, I used a 9" thin kerf blade.

Yet another option might be to use a bandsaw to create the appropriate kerf in your part. Then glue some blocks in place to hide the sides of this cut. If you have a tall enough ceiling over your table saw, you could also create an oversized tenoning jig type arrangement to make a similar cut.

Depending on your hardware, you might also be able to use a biscuit cutting tool to make the cut, though in my case that cut wouldn't be deep enough for the hardware I had purchased.

Many ways to make that cut, just think outside the box, but also spend an appropriate amount of time controlling your part or tooling in order to ensure you can do so safely.

Regards,

Grant in Iowa

Re: How To??

#4

Here's how I did it

Ralph Lipeles

I had to make a new bed side rail a few years ago. I faced the same problem as to how th make the slit cut in the rail ends. First, I made 2 assemblies to fixture my skil saw. The fixture pieces were each made from 2, 1/2 by 6 by 12 pieces of 1/2" plywood. Screw them together along the 12" long edge. Now add 2, 6 by 6 triangular sections of plywood to make the plywood "L" sections more rigid. Now you can clamp these fixture pieces to the end of the new bed rail. Position them so that they will act as a support for your skilsaw. Just align them carefully with respect to each other and located properly with respect to the end of the new bed rail. I then clamped a piece of scrap wood across the 2 fixture assemblies to act as a guide for the saw, made a cut and then moved the guide strip slightly to cut a little more to achieve the cut width that I needed to fit the metal piece.

Re: How To??

#5

Re: Hmmmm

Mark Mandell - Gone Round In Jersey

I've split the old rail and find the original cuts (1-3/8 deep with 1/8" kerf were done with a circular blade.

As I don't have a radial arm amputation saw, it appears I'll be cutting the slots with the band saw and the filling the ends of the kerfs with like wood for the disguise. Original rails were 3/4" with the hooks set in the center. I think I'll add a bit of beef then do the kerf off center to give things more heft. The originals were glue ups so a single 1" board should be quite a bit stronger. Now I have to dig out the maple that got dead stacked under a half ton of cherry and walnut. Would be at about the bottom of the stack don't ya know.

Thanks for the input guys.

Re: How To??

#6

Re: Hmmm

Barry Irby

Got enough room above your TS to stand the piece on end? Would be pretty easy if you do.

I don't, so I would have to drag the saw out into he drive way or try one of the wild man methods mentioned above.

Re: How To??

#7

Re: How To??

Jesse Cloud

How about this:

Machine the wood for the rail two TS kerfs extra wide. Rip off each edge to leave just the amount of material in the slit. Cut the slits through with a bandsaw. Glue up the two pieces you cut off and you have stopped slits....

Re: How To??

#8

That's how

Mark Mandell - Gone Round In Jersey

it was done before. The rails are actually 2-1/2 pieces that had the kerfs put in the ends on a table saw (boards on edge) then glued together leaving the semicircle cut into the end grains. The glue joints are where both rails failed and then the stress put on the steel dowel retainers split several of the ends again.

I think I can do better than that.

Thanks again.

Re: How To??

#9

Re: That's how

FredD

That hardware sounds like cheap to me Mark.

Every Bed rail I have made or replaced , I used hardware that was a steel plate with two hooks on it and the plate fit into a mortise in the rail end.

Same thing for the post except the steel plate has two slots to receive the hooks.

http://www.rockler.com/product.cfm?page=10&sid=AFL91

FredD

Re: How To??

#10

Yes, Fred,

Mark Mandell - Gone Round In Jersey

That's exactly what I have. A 1/8" [m.o.l.] steel plate that is inserted 1-3/8" deep and held in the slot mortise by 2 steel pins. My issue is how to cut the mortise which was sliced into the ends about 2" deep.

Re: How To??

#11

Re: Yes, Fred,

paul in AZ

Mark:

My bed has the fasteners Fred linked to. I may have got it backwards but I put the male plate on the rail end and the female into the bed post. This meant only a small amount of chiseling in the end grain to recess the male plate. Even that may not have been necessary. I cross drilled the rail and put in half inch dowels to give the mounting screws something other than end grain to bite into.

In addition to recessing the female plate to be flush with the post I used a drill bit and chisel to cut the appropriate depth slot to receive the hooks.

Re: How To??

#12

That's correct...

John in NM

Or at least that's how I always did them too. I used to cut the mortises for the female side in the bedpost before it was glued up using a mortising machine, and cut the male side in the end of the rail using a router and a jig made for the purpose. I recall substituting longer screws, 1 1/2" or more, for those provided. If the mortise is as tight as can be, the sides of the mortise bear most of the weight, and the screws just keep the plates from rotating out of the mortises.

Back to Mark's problem though, I'd substitute this kind of hardware for that which it came with. You said they were bunk beds? Probably boys' bunk beds? Maybe you need wedged through tenons with grade 8 cross bolts :D

Re: How To??

#13

Re: Yes, Fred,

FredD

Look at the link I posted Mark ,

FredD

Re: How To??

#14

Re: Yes, Fred,

FredD

That is right , Paul, and like John says , the mortise supports the weight and the screws hold the plate in the mortise , just like a door hinge.

I wouldn't depend just on screws to carry the weight , the mortise is necessary.

FredD