Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

paint brush cleaning question

Posts

paint brush cleaning question

#1

paint brush cleaning question

Bill Tindall

For me, this is particularly a problem with latex paints. Say for the purposes of this question one dips the brush into the paint 2". At the 2" line on the bristles a layer of partially dried paint develops (especially at the rate I paint). When it is time to clean the brush this band of partially dried paint at the 2" mark is particularly difficult to remove. This problem is so annoying I suspect professional painters must have figured out a way to better clean it or avoid getting it. What is the best way of removing this band or preventing it from forming?

I clean by rinsing with lots of water whilst working the bristles, then hot water and combing. The combing eventually pulls this rubbery paint out of the bristles, but it takes a long time.

Philosophically, I buy the highest quality brushes and take care of them, so this cleaning thing is important.

Re: paint brush cleaning question

#2

Re: paint brush cleaning question

Randy Johnson

I've always used a wire brush like welders use. That and soapy water seems to do the job.

Re: paint brush cleaning question

#3

Jason Roehl in Lafayette, IN

A couple things...

Jason Roehl in Lafayette, IN

First, you shouldn't be dipping your brush 2" into the paint... ;) If you want the brush to hold more paint, you need to get the bristles to separate, which you can do by tapping the tips of your bristles on the inside wall of your paint bucket after you dip. If you need less, tap the sides of the bristles; (almost) never scrape. You also shouldn't have to dip more than 1/4-1/2".

Second, what the others said. I use a brass wire brush for cleaning the outer bristles, and a brush comb to help straighten them and get water to the inner bristles. Don't spin the brush, but whip it out with a sharp, quick, downward motion (remember to hang on to the brush, they can bounce quite a ways--DAMHIKT).

Third, I don't worry about a little paint residue on the outside of the bristles. More of a concern is that I can dip the brush to the ferrule in clean water/solvent and have the water/solvent stay clean. Once the brush is fully dry, you should be able to pinch your finger almost all the way together through the uppermost part of the bristles next to the ferrule. Once the uppermost 1/4" or so gets hard, the brush is toast.

Oh, and if you get a straggler bristle, break or cut it off...

This is just what I do. But you know what they say about opinions and "rear exits"...

Jason (Addy protocol: pro painter)

Re: paint brush cleaning question

#4

Clint Searl

Re: paint brush cleaning question

Clint Searl

After an initial rinse under the hose, I work the brush with liquid laundry softener, followed by a wash in hot dish washer soapy water and brushing with a stiff brass or stainless bristle "tooth brush." A couple rounds of that will take care of it.

I always start with a wet brush and do interim rinsing for long jobs.

Clint

Re: paint brush cleaning question

#5

Soap is a huge help!

John in NM

I use a little dish detergent with hot water after an initial rinse or two, when I get to the combing stage. If you have some that have dried paint, try a brief soak in lacquer thinner (10 min or so, not overnight). This doesn't do the brush a lot of good, but if you were going to pitch it anyway its no big deal. If the bristles start coming out as a result, toss the brush. I've saved several from work this way - none of the other guys has any patience for cleaning brushes - and I've yet to have any start to shed.

I do the soap and water on oil paint too, after several rinses and shakes in solvent. I rinse with alcohol or acetone after shaking out the water from the wash, as Jason described. If the bristles are synthetic I don't think you need to do that though, water won't hurt them. I find poly and oil paint easier to clean out personally.

Re: paint brush cleaning question

#6

Re: paint brush cleaning question

FredD

Like you I buy good brushes , because they give better results and last longer when cared for.

If your painting with Latex in hot weather or going slow enough that the paint is forming strings on the brush , take the time to clean it.

I use household Ammonia mixed with hot water and Dawn detergent, works fast.

If you let the paint dry and its Latex , then toss it. Some advocate Vinegar for dried Latex paint, I haven't had much luck with it.

I for one do not use metal bristle brushes to clean filament brushes , seems like it would be harder on the brush then necessary.

Combs are fine for brushes, not metal ones.

Not a good idea to use Animal hair brushes with water base paints either, it swells the base and the Ferrule permanently.

Regardless of the finish wet the brush a little with the solvent, in this case water before you start, it makes it a lot easier to clean.

FredD

Re: paint brush cleaning question

#7

Re: paint brush cleaning question

Bill Houghton, Sebastopol, CA

I clean with mechanic's hand cleaner, which I believe is dish-type detergent and either mineral spirits or a citrus oil, depending on brand. After the first cleaning, residual mineral spirits/citrus oil seems to make the brush a little more resistant to paint sticking to it, although on hot days this is still an issue.

Like you, I use a brush comb, and between this and the mechanic's hand cleaner, it goes fairly quickly.

I concur with others: clean more than once a day if it's a problem.

Re: paint brush cleaning question

#8

JL

Re: paint brush cleaning question

JL

I pre-wet the brush with water and then "sling it out". It seems to help me clean it later.

Re: paint brush cleaning question

#10

Goof-Off

Rod Peterson�Ormond Beach, FL

I keep a spray bottle of it around. It's always step two in my cleaning process with latex paint. Warm to hot water first, Goof-Off next, brush with painter's brush/comb combo, warm to hot water with laundry soap, rinse. I do spin to clear excess (sorry, Jason) primarily because I was taught early on not to "whip" the brush (sorry, Jason).

I think one of the most important steps is to form the bristles back into their original shape while wet before setting aside to dry. Usually, I later put the brush back in its original package (Purdy brush packs are designed specifically to do that—don't know about others because I've only bought Purdy in the last twenty years). I don't like to put them in wet because I don't want the cardboard to distort or deteriorate.

Years ago I watched an artist on PBS clean his big brushes (used to cover large areas and essentially a 2" or so brush such as we're talking about here) by dipping in solvent and then whapping them back and forth across one of his easel legs to clear the excess. I've done that, but for some reason I don't often have a convenient surface to do it on. SWMBO doesn't appreciate it on chair legs, for example.

Rod

Re: paint brush cleaning question

#11

Re: paint brush cleaning question

ThomD

There do seem to be a variety of brush cleaners that are sold for this purpose. For myself, I use something called paint brush conditioner. I think I bought it at HD. At the time it was in a plastic tube like some toothpaste or sunscreen comes in. For all the world it felt like hand cream except it dried fast. You just rub it over the brush, paint, and then when it comes time to wash, the paint just peels off. Another thing is to use only synthetic brushes these are less absorbant and do not bond well to the paint. My Great Uncle used to be a machinist who set up brushmaking machines, but I have to say I am semi sold on the chisel brushes that come from the dollar store. Not quite the equal of the 20 dollar brushes, but nearly so, and I do try to spin them along with careful washing.