Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

How to attach shelves to angled side?

Posts

How to attach shelves to angled side?

#1

How to attach shelves to angled side?

Brint in Richmond, VA

I'm designing built-ins for my attic "bonus room" which is under the eaves. The outside panels of each built-in butt up -- and run flush -- against the angled ceiling. I was wondering what the best way would be to attach the shelves to the outside panels (in the attached image, to the left side). I expect to cover the edge with a bit of face framing, so I have a little room to work with.


Re: How to attach shelves to angled side?

#2

JL

Re: How to attach shelves to angled side?

JL

When I built a similar project, I put cleats above and below the shelf. I suppose you could also dado the diagonal piece.

Re: How to attach shelves to angled side?

#3

Re: How to attach shelves to angled side? *LINK*

David Yoho

Brint, seeing you're local to me, I first checked Woodcraft for the part I'm thinking about but they don't appear to carry them. However, Lee Valley does. Although you could go several directions with this (i.e. - angled dado, cleats, biscuits), another invisible alternative is hidden shelf supports. I've included a link to those at Lee Valley. If you order now, the shipping is free.

David


Lee Valley hidden shelf supports

Re: How to attach shelves to angled side?

#4

Re: How to attach shelves to angled side?

David Hay Denver

Based on the steep angle you have there, I'm not sure if an angled dado would work. It seems like you'd end up cutting through the angled piece completely in order to provide enough of a shoulder for the bottom edge of the shelf to rest on.

I'd probably suggest going with biscuits, dowels, or some kind of cleat to make the attachment, perhaps with some screws (assuming the outside of the angled piece won't be seen since it's up against the ceiling)

I suppose you could also do a series of through tenons, but that may be overkill for this project.

David

Re: How to attach shelves to angled side?

#5

Kneale Brownson

Re: Second the cleats

Kneale Brownson

I'd go JL's way, especially since you'll have the face framing to hide the cleats.

Re: How to attach shelves to angled side?

#6

Vertical divider?

Pat Evans

You could put small vertical dividers at the sloped end. The slope precludes full height use of the shelf in that area anyway, and the dividers would give you a small knick-nack cubby hole. Furthermore, you could make the shelves adjustable that way. Just make a new divider if you change the shelf height.

Re: How to attach shelves to angled side?

#7

Re: How to attach shelves to angled side?

Barry Irby

I would suggest you put a second layer in the left hand end. Assuming you are having a facing, it would be invisible. If two thickness of full thickness material are too much, you could make the full length end (as shown) out of something thinner, such as 1/4" plywood and then laminate the full thickness pieces between the shelves. In this way, you have created "rabbets". All the angles would be consistent and say, no special cutters or skills required. Might make the plywood in two or three strips to avoid "cross grain" connection issues.

Re: How to attach shelves to angled side?

#8

Alan Young

I like the verticel divider concept

Alan Young

That's how I approached it in a similar build. I made the vertical dividers a structural part of each section. Stacking as we went. The top was inserted at the end and trimmed off.

-Alan






Re: How to attach shelves to angled side?

#10

Re: How to attach shelves to angled side?

FredD

Barry's idea of a double layered end with the inside layer forming slots for the shelves,certainly wouyd the strongest yet mentioned and fast to do as well.

FredD

Re: How to attach shelves to angled side?

#11

Ellis Walentine

Agree

Ellis Walentine

Re: How to attach shelves to angled side?

#12

How to attach shelves to angled side?

Brint in Richmond, VA

Y'all are great -- thanks so much for the help.

I think I'll go with Barry's suggestion of a double-layered end piece, as well as a few vertical supports (thanks, Alan - the photos really helped). That will let me make them adjustable. Besides, the bottom shelf is 52", which is way too long without one.

David, thanks for the link to the LV product. I used those once in college putting together some pre-fab Ikea bookcases, and they're still working great (um, 30 years later...!)

I'll post pics later.