What's bad about black walnut?
David Frame Jr. Good Afternoon Gentleman,
Earlier this morning, I had a conversation with Todd at Whiteside Machine Company. I own several of
their up and down spiral solid carbide router bits of different sizes. This is the first time I've had a 1/2"
down spiral bit burn the tip up in a matter of about one hr. More mortises need to be made in the 3 in 1
crib I'm building for my expectant grandson. So, I'm touching up the bit up with a diamond stone. If I
change the bit now, it will throw the mortise off. The plunge router is connected to a special base I made.
This is the first time a solid spiral carbide bit burned the tip on me. Believe me when I say, "I use these
bits all the time," Clean them when finished, dip them in 3 in 1 oil and put them back in their own
plastic cases.
Todd at Whiteside said that black walnut contains silica, which can burn the cutting edge off a bit in
minutes if to much of a bite is taken at a time. He also mentioned that breathing in silica it contains, is
bad news. My Jet DC-1200W-1 Limited Edition with a two way 4" port connected to the
squirrel cage, catches the major part of the wood chips, but not fine airborne dust.
Since working with wood for the past 37 years, I've recently developed an unmanageable cough when I
drink or eat, and my breathing is much more shallow. I don't smoke and have managed to contact
COPD (Chronic Obstuctive Pulmonary Disease) from the airborne dust with some of the woods I work.
My doctor confirmed this with an x-ray
a week ago.
The moral to this story is to wear, at the very minimum, a cheap dust mask or better yet, a good one.
Maybe, buy organic respirator, if you don't already have one for spraying finish. And last but not least,
build or buy a fine filtered dust collector. I own three squirrel cages. You would think I would have built
one by now.
Adios until next time,
David Frame Jr.
- - -
Hi Everyone, I'm new to creating a personal profile about myself. But then again, how will you ever know me if I don't. Anyway, after dropping out of school at the ripe old age of 14, I want to work as a pump jockey at a full serve, service station. you remember those, don't you? I didn't have a work permit, but they needed someone to pump gas, check oil, and the other things we do to keep their vehicles running. When I turned 15, I got a work permit and asked someone, A regular that came into the gas station for a job. A Mr. Edward Cannon said that he needed someone to help carry heavy things around the shop, to help others, and to keep the shop clean. I had no idea what I was getting into. The one thing I do recall is that the pay was double what the gas station was paying. From $1.55 an hr. to $3.10 an hr. that was a big difference back in the early 70's. I went to work for a shop that fabricated interiors for crew, tug, work, and ferries. We made the pilot chairs, passanger chairs. foldable bunkbeds for the crew, and some large and small booths in the lower decks on some of these boats. At 15 yrs. old, this man, Ed Cannon and his business, Eacco Marine Seating and Metal Fabrication, took a kid that was wet behind the ears and turned him into an all around woodworker, seamstress, upholsterer working foam padding for the sewn seating, a painter of wood, stainless and aluminum, and someone that had no direction and turned him into a man with a lot of responsibility. After about 3 months, I was trusted to open the shop, begin my own work or help someone else do theirs and no one ever suspected me of wanting to steal, tear the place up, or any of the stupid stuff kids do. I was well trusted by everyone in the 8 to 10 person shop. Sometimes, I drove to areas of south Louisiana, that I'd never been to before, delivering the interiors for the boats as well as taking measurements with a story pole for the booths we had to construct. A boat sits in the water bow up. when we fabricated the booths, they were constructed on an angle, level with the boats bow and stern. I'd say anywhere from a 7 to 12 degree angle. After about 3 and a half yrs., I was looking to make more money. Mr. Cannon offered me a raise, but oilfield money was to good to pass up. I've been all over the world drilling for oil, but the one thing I miss is working for Mr. Cannon at Eacco Inc. It was he and a fireman that taught me basic woodwork with power tools. I bought books upon books to learn everything I thought I wanted to do at the time. Will finish later... David Frame Jr.