Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Angled tenon making?

Posts

Angled tenon making?

#1

Angled tenon making?

Tony - Memphis

I'm building a couple of chairs. There are no 90� angles on these things! I've figured out ways of cutting the angled tenons, but nothing I'm happy with. Fo the exposed joints, I cut them close and then finished them with a chisel. That works and might still be the best way to go. For the parts like the backs that will be covered, I cut the end of the stile to the appropriate angle (2� in this case), then just used my tenon jig on the TS to cut the cheeks and nibbled away the rest out to the shoulder. Not pretty, but it works ok. Anyway, just got me to wondering what other folks do. I've seen a couple of router jigs that looked interesting. Just read an article y Pat Warner on his jig to do tenons. I guess regardless of the technique, fitting by hand will always be required if you really want tight joints. That's subjective I know, but I like to try and get them really tight. I'm not always successful, but I try! I don't have any pictures with me of my progress, but these chairs are my take on a lolling chair. I used lots of pic's on the web, Norm's plans, etc. and came up with my own design using Sketchup. I'm still tweaking the arm design. Almost ready to start on those. The backs are getting close to being finished. Just need to bandsaw the curves and then glue them up.

So, how does everybody else do their angled tenons (or straight ones fo rthat matter). Oh, for straight, I use teh Delta tenon jig for the cheeks, cut the shoulders with the miter gage, and then tweak by hand. When I took a class with Phil Lowe once, we had to chisel the tenons on all four tenons for the sides! That was too much!

Tony

Re: Angled tenon making?

#2

Re: Angled tenon making?

Bob Lang

The trouble with trying to do these by machine is that you usually need to make at least two perfect setups, one for each side. In most cases you need to make four different cuts. I think this is a place where cutting the shoulders by hand makes more sense. You can machine cut some angled blocks to use as guides for the saw until you have enough practice in to confidently cut without them. You can cut most of the cheeks on the band saw or with the tenoning jig at the table saw. The little bit left next to the shoulder can be popped out with a chisel. Cut wide and trim back to your shoulder line.

Bob Lang

Re: Angled tenon making?

#3

Ellis Walentine

How about loose tenons?

Ellis Walentine

A dedicated slot mortiser is probably the simplest way to create this type of joint, but you can do them with a router. In either case, you will need to make jigs to orient your workpieces to the mortising bit. If the mortises are in the middle of curved or compound-curved parts, this can be pretty hard to do. Another approach is to drill out the mortises and clean them up with a chisel. If you drill accurately, the holes act as gauges for paring, so it usually turns out pretty accurate.

Ellis

Re: Angled tenon making?

#4

Re: Angled tenon making?

Tony - Memphis

That's exactly what I ran into. To cut the shoulder corerct on each side is almost impossible using a miter gage and changing setups. That's where I figured knifing the line and cutting close to it and then finishing by hand was the best. Unfortunately, I'm not that good. But I'll keep practicing. At least I feel like I have the concept down. Just being careful and patient goes a long way. I rarely make a tenon to fit by machine. I usually try and cut just outside my pencil line then bring it home with a rabbet block plane or a shoulder plane. I'm getting better at that. Getting the rabbet block plane setup is a bit of a challenge. I've also discovered that the tenon cheeks off the TS aren't exactly flat. I assume things move a litle, blades fles a hair, etc. I thought it was my plane, but it was cutting true and flat.So, the joints might actually be a little stronger finished by hand too. Who knows.

Thanks,

Tony

Tony

Re: Angled tenon making?

#5

Re: How about loose tenons?

Tony - Memphis

I'never tried loose tenons, but I thought I might after a couple of times that I cut the shoulder line instead of the overall length - oops. I've seems some instances where I thought they would be a good option. That's something I need to try.

Thanks,

Tony

Re: Angled tenon making?

#6

I'd angle the mortise...

John in NM

Now that I see the pic you posted today... Too late now :D, but something to keep in mind for next time. It can also be a tricky problem to solve, but its stronger when you're done. On some designs you can keep the back leg square to the mortise and let it be angled relative to the front of the chair. Some of this stuff gets much, much easier with hand tools of course.