Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Sensor light switch question?

Posts

Sensor light switch question?

#1

Sensor light switch question?

Barry Irby

I built an exterior closet on my shop and the Air Compressor and DC are out there. I like the fact that it made room in my small shop and gets the noise and dust out side. But, The Compressor has a slow leak and it runs once in a while. I am afraid that someday it will develop into a big leak and burn itself up and the closet happens to be under my bedroom and I can hear it better form there than from the shop, so, I turn off the breaker for the circuit when I leave. At least, I do sometimes and the rest of the time I have to go back and turn it off. Then I have to turn it back on when I return. One of life's little PITA's. What I am wondering is could I use one of those sensor switches that "sees" when someone in present and turns the light on? In this case, it would keep the compressor receptacle energised while I am in the shop and turn it off when I leave. Will those switches handle a 1 hp compressor?

Re: Sensor light switch question?

#2

Couple of possibilities

Bill Houghton, Sebastopol, CA

I wouldn't expect one of those sensors to have enough gumption for that kind of load. If you're going to do the sensor thing, you want the sensor to operate the switching side of a relay or contactor* rated, on the switched side, for your compressor.

The weak part of this design is that you now have two components that can fail: the sensor and the relay. The latter may not be a problem if you buy a commercially-rated contactor. I've had a contactor in my hot tub for well over a decade, operating in sub-optimal conditions (high humidity, ants, outside), and it's still going strong. The sensors, though, can fail pretty fast; the one we had to put in our one bathroom lasted maybe a year. I don't know if there are commercially-rated sensors with better life expectancy.

*I think the difference is that a relay is a black box, while a contactor has its operating bits right out there in the sunlight, and thus needs a rated box to hold it. Contactors are better because they're easier to diagnose.

Another alternative would be to buy a timer for that circuit, and turn it on when you're in the shop. I like the mechanically wound type, but they're hard to find; I understand Intermatic, which made them for generations and which was the standard, is getting out of the business. The advantage of mechanically wound timers is that you can see, right there staring you in the face, that it's working or not.

Myself, I'd favor the second choice, IF you can track down a good Intermatic or similarly robust timer.

Re: Sensor light switch question?

#3

Re: Couple of possibilities

Barry Irby

Thanks, I will think on that.

Re: Sensor light switch question?

#4

Jason Roehl in Lafayette, IN

Another idea

Jason Roehl in Lafayette, IN

Another idea would be to wire the relay to the lights for your shop. You remember to turn those off, don't you? That way, the compressor can come on when you turn the lights on to go in the shop, and it's off when you leave.

Jason

Re: Sensor light switch question?

#5

Re: Another idea

Barry Irby

I wonder how many amps are on my lighting circuit now? A lot I bet. I will think about that and see if there is room for the compressor. Could just wire a receptacle for it onto the lighting circuit.

Re: Sensor light switch question?

#6

Jason Roehl in Lafayette, IN

Re: Another idea

Jason Roehl in Lafayette, IN

That's why I'd use the relay. A relay will draw minimal current, allowing for use on your lighting circuit, but the other side of the relay would probably need to be on a separate circuit for the compressor. Compressors, in my experience, tend to draw quite a bit of extra current on start-up, particularly when they're cold, but already have pressure in them.

Jason

Re: Sensor light switch question?

#7

Re: Sensor light switch question?

jerryburns

Barry

You do not need a relay just put in a Heavy duty swith to turn on recptical for you air compressor mounted next to your light switch IF it is 120vac air compressor if it is a 220 vac unit you will need to to do the relay thing

Re: Sensor light switch question?

#8

Jim DeLaney, Austintown, Ohio

Re: Sensor light switch question?

Jim DeLaney, Austintown, Ohio

I just wired a light to the same switsh that controls my compressor. When the compressor is on, so is the light. That way, when I turn out the shop lights, the compressor light is still on as a reminder to shut it off.

Jim D.

Re: Sensor light switch question?

#9

Another idea  Fix the leak

del schisler

Re: Sensor light switch question?

#10

Actually, that's the best idea....

Barry Irby

I should grow up, put on my big boy britches and hunt down and fix the leak. I did that on my other compressor that is usually in this location, but it is out on a job right now. I just don't feel like doing it again. and, even then it would be a good idea not to leave it powered all the time. Never know when it might blow a gasket and run itself to death or start a fire.

Re: Sensor light switch question?

#11

Rick L

Re: Do not use the circuit breaker...

Rick L

as a switch. It will trip easier in the future. A circuit breaker is not a replacement for a switch. The intermatic timers are easy to find at mcmaster. The light sensor isn't high enough amperage for the compressor by itself.

Fix the leak and get a switched outlet and put switch over by the main light switch by the door so you can shut the compressor as you leave the shop.

Re: Sensor light switch question?

#12

Re: Actually, that's the best idea....

Stuart Johnson

I don't like to leave the compressor on regardless of leaks. What would happen if the hose got nicked and developed a weak spot that gives way one day when your aren't home? I think the best approach is a switched outlet with a light.