Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Question on saw blade and warping

Posts

Question on saw blade and warping

#1

Question on saw blade and warping

Robert R. Clough - Thorncraft

First, perhaps I am "sawblade challanged"! From my reading about GP and Comb blades, I sometimes think they are the same, but then . . . Perhaps a Comb blade is literally a combination of rip and crosscut teeth, whereas the GP blade is a what? I have both and have not noticed much difference.

Comments please.

Second, I just finished a chest/seat for my youngest Grandson (Red Elm - the wood not the boy). I left it in the garage - and we have had lots and lots of rain. The seat warped! I brought the seat itself into the house and it has un-warped. Now, should I add cleats to the bottom using, of course, proper sliding/elongated screw holes for expansion? They will not be seen - obviously.

Again, comments, please.

Re: Question on saw blade and warping

#2

Lee Grindinger

Vague terms

Lee Grindinger

I assume you're referring to general purpose and combination blades. They could be essentially the same but these are somewhat vague terms.

Either term would probably refer to an ATB (Alternate Top Bevel) with or without a raker, a flat top tooth. These blades will often have gaps for chip clearance between sets of teeth.

Crosscutting requires ATB teeth set close, chip removal is not as large an issue since the wood fibers are being cut across so particles are smaller. Ripping is more about waste removal since the chips are longer and larger, and since you're cutting with the grain tear out is not as large a problem.

Combo blades are quite nice but if they do well crosscutting it comes at the expense of ripping which will bog and create a lot of heat. Having said that I rarely changed blades to a ripping configuration unless I had a lot of ripping to do.

Lee

Re: Question on saw blade and warping

#3

Lee Grindinger

Oh, as to the the warping...,

Lee Grindinger

Chests can be problematic since the outside is subjected to very different conditions than the inside. A better film could help slow the uptake of moisture into the outside face of the lid evening the cycles a bit and once the chest is moved into the house the extremes won't be as severe.

A cleat may destroy the top if the moisture difference between the faces is enough to overcome the restraint. My first tact on this one would be to let it flatten, add a few more coats of finish (What did you use?) and move it indoors. Then see if the problem resurfaces.

Lee

Re: Question on saw blade and warping

#4

Ellis Walentine

Blade nomenclature

Ellis Walentine

As Lee said, general purpose and combination blades have alternating top bevel teeth. Combination blades are typically 50-tooth blades with ten sets of "4 and 1" ATB and raker teeth. General purpose blades may have only ATB teeth, though they are likely to be lower angle tips, say 5� to 10�, than strictly crosscutting blades, which have regular (15� to 20�) or high-angle (Hi-ATB. 30� to 40�) tip angles. Neither blade is as good for crosscutting and ripping as blades ground especially for those purposes.

Regarding your chest/seat, I'm not sure what part of the chest the seat might be. Is it a flat lid? A couple braces might be just the ticket. Ideally, you'll engineer the cross section and species of the brace to be stiffer than the warping forces it will have to withstand. Sliding dovetail ribs might be the ticket, or slot-screwed braces as you suggest, allowing for enough movement in both directions.

Ellis

Re: Question on saw blade and warping

#5

to add to Lee's good advice

Bruce, a MN Galoot

make sure that both sides of the seat/chest are finished after you bring it in and it has flattened out again. It slows down differential moisture absorption.

Re: Question on saw blade and warping

#6

Re: to add to Lee's good advice

Robert R. Clough - Thorncraft

No finish yet but it shall be polyurethane. Children, especially 4 yo, are hard on furniture so it must be tough.

Ok, no cleats (thank goodness - I detest them).

Re: Question on saw blade and warping

#7

Re: Blade nomenclature

Robert R. Clough - Thorncraft

Elllis. I use my GP/Comb blades most of the time except when I must have extra special cuts - then it's the crosscut and/or rip blades. Two of my comb blades are Freud and one is Forrest Woodworker II.

The seat I speak of is actually a lid but since the piece has a back and arms as well, I think of it as a seat.