Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Questions for Dave Paine on Flatmaster

Posts

Questions for Dave Paine on Flatmaster

#1

Questions for Dave Paine on Flatmaster

Barry Irby

Didn'T want to hijack the thread on the Baby drum Sander.

How does this unit differ from the Sand Flea?

It seems to me that the soft sandpaper would not produce a truly flat surface and would tend to round over the corners. Are you getting good results? Crisp and flat? Can't you taper a piece pretty easily? I like the look of it, but I am skeptical.

I also have a Performax 16/32 and have had good results with it. I saw a Sand Flea at a WW show and then made a table to sit on top of my performax and can sand on the top side like the Sand Flea. I find it very useful for some things, but it is easy to change the dimensions of small pieces if you get heavy handed. And if you don't move pieces at an even rate you gets dips and scallops in the surface. I tried to make about forty 3/4" square matching pieces and sanded them with the Performax. Since they were to be side by side and 3/4" apart, any variation in the size turned out to be obvious. I sanded some of them in the Sand Flea mode and it made a huge difference.

Re: Questions for Dave Paine on Flatmaster

#2

Re: Questions for Dave Paine on Flatmaster

Dave Paine

Barry, I thought of the Sand Flea when I saw the Flat Master being demo'd at the WW show. I walked by, then picked up on "no heat" and walked back, then after the demo plonked down my money.

I did not stay for a Sand Flea demo in an earlier show, so I can only say that both units have the drum below the table.

I read your thread about making a table for the Performax and was tempted to do so.

In my Performax I have trouble keeping the piece parallel. In my case I somehow manage to get the piece thinner in the middle than the ends. I even made a sled to support the piece and carefully support on in feed and out feed, but somehow still get thinner in the middle.

The Flat Master uses hook and loop drum and paper. The demo talks about the paper being lifted by centrifugal force. This makes sense, since the hook and loops do have some give. The quieter operation likely results from just the paper being pushed against the piece by centrifugal force and not mechanical pressure as in the Performax.

The major difference in the Flat Master vs Performax is lack of heat when sanding. I can sand coatings without gumming up the paper.

The table top is not as deep as I would like, so I will be building deeper version. Since the user pushes the piece across the drum, it does need a consistent feed rate, although the small removal per pass means easy to remove in a subsequent pass.

The Flat Master produces very fine dust but the material in the drum does not create electrostatic, so the dust particles are easily vacuumed.

I have been able to achieve a flatter reference surface than with the Performax, and use my planer to get the piece parallel.

I also get much smaller lines in the piece. This may be due to using 100 and 220 grit, although I also have 320 and 400 to try later. In the Performax I use 80 grit since I found trying to use e.g., 120 grit resulted in burning of abrasive and then the wood. In my early attempts I managed to burn a piece on first use. I later changed to the Klingpor Zirconia abrasive, which is terrific and creates less heat, but not as little heat as the Flat Master.

I am using the Flat Master every time I am in the shop.

I mentioned the as-purchased fences were useless. I made one of my own which is dead on 90 deg and not can use Flat Master for edge sanding. Something you would try with your converted Performax. Edge sanding results were also impressive.

I hope this helps even though I have no real data on the Sand Flea.

Re: Questions for Dave Paine on Flatmaster

#3

Re: Questions for Dave Paine on Flatmaster

Barry Irby

Thanks Dave.

Let me hammer one question. Does it round over the edges/corners of the boards? Just seems to me the sand paper would roll around the edges.

I can see a lot of advantages to this design. (Open top, regardless of what the drum and sand paper are.) There is no limit on the thickness. If you and manage the piece, you can slide anything across it. With a little care, you can use it to "joint" drawers. You can sand the side of a drawer that is already assembled, but a few thousandths too wide. I find I can sand very small pieces by setting them on the out feed table and dragging them back over the drum. I took the spindles I mentioned and sanded all the corners on them quickly.

I have not real complaint with my Performax. Always been very accurate. I expected it to be slow, and it is. But, I sanded the 40 pickets about 8 at a time and it kept them all square and straight and nearly identical. It was something of a mind bender to keep them all lined up and rotate through the four sides and keep them sorted. (Used Colored chalk, would have been a nut case without it.) Having both options is terrific. It is a chore to run some woods through the Performax without burning. Fresh paper, fast feed, very light touch.

Re: Questions for Dave Paine on Flatmaster

#4

Re: Questions for Dave Paine on Flatmaster

Dave Paine

Barry,

The edges do not get rounded. I can understand why this would seem to be possible, but it is not happening - so far.

The setup is meant to be with the finest grit paper just touching the wood, or a tad below. I set up with 220 grit and barely touching. If I push a piece across the top with the motor off, I can hear a faint scratch but the drum does not move. Changing to heavier grit does move the drum.

Like the Performax it takes patience. Many passes with small removal each pass.

One aspect of the machine I like is that due to the low noise I can hear where the wood is being sanded on a given pass, and like your Performax technique I can work on certain high spots first.

Re: Questions for Dave Paine on Flatmaster

#5

Thanks Dave

Barry Irby

I had forgotten that the set up is to just let the sandpaper barely kiss the wood.

I have to say though that sanding all those pickets was a revelation. The Performax was doing a good job but I got impatient. There were several that needed just a little touch up on one or two sides. My thought was that rather than run ALL of them through the Performax on TWO opposing sides, I would just sand the spots in the Sand Flea or Flatmaster mode. Probably did not take off a 1/100" but the lack of uniformity was OBVIOUS. And it became apparent that they were getting out of square quickly. Something to watch out for.

If I had the money and the space, I would have a Flatmaster In a minute. It does appear to me that it needs a larger table through. Hmmm. Another thing to build into the wing of my TS along with the router. Double Hmmm. They could be interchangeable.