Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Table saw and Jointer Table - cleaning/preserving

Posts

Table saw and Jointer Table - cleaning/preserving

#1

Table saw and Jointer Table - cleaning/preserving

David Lykins - guitardude - Dallas GA

OK, yea I haven't posted here in eons, and just moved my jointer to a more "ergonomic" area in my shop when I noticed that the table could use some attention. I remember one time cleaning my TS table with WD-40 and a VERY fine emory cloth or cloth backed sanding paper. seemed to work pretty good but not real sure its good for passing the wood over an oiled table even though I did thuroughly clean/wipe it off.

So I was just wondering how you guys keep your table tops smooth and clean. I saw one guy that used silicon spray, just wiped off the table top and sprayed it down. Wasn't sure if that would effect the wood or not.

Any suggestions are greatly appreciated. I actually have a chance to do some comissioned wood working, so I know I'll need my TS and jointer working good. You'll also be happy to know that I purchased an Incra Miter 1000HD.... All I can say is "WOW!" I should have got one of these years ago, what a GREAT addition to my TS.

Thanks a bunch in advanced.

David

Re: Table saw and Jointer Table - cleaning/preserving

#2

JL

Re: Table saw and Jointer Table - cleaning/preserv

JL

I use paste wax or something like Renaissance wax to coat it. I usually clean with an abrasive pad. If there is rust, I use aluminum foil and a little bit of water.

Re: Table saw and Jointer Table - cleaning/preserving

#4

best stuff

del schisler

i use this work great T9 and boeshield mfd by boeing aircraft lots of supplyers have this

http://www.boeshield.com/

Re: Table saw and Jointer Table - cleaning/preserving

#5

Re: Table saw and Jointer Table - cleaning/preserv

David Hay Denver

Whenever I need to give my cast iron tables a good cleaning, I use WD-40 and a synthetic steel wool pad (i.e. scotch brite pad), wiping it off really well with paper towels. I'll then give it a coat of paste wax...whatever I have laying around the shop. Just make sure it doesn't have silicon in it...it can wreak havoc with the finishing process. I've used the T-9 Spray as well, but it doesn't seem to last or work any better than paste wax...and it's more expensive, if I remember correctly.

David

Re: Table saw and Jointer Table - cleaning/preserving

#6

Re: Table saw and Jointer Table - cleaning/preserv

Bob Entwisle in NJ

Hi David,

I use whatever amount of abrasive, usually just a scotch bright pad, to clean with, and paste wax to preserve.

I have tried the Boeshield T-9, but I've found that two heavy coats of past wax seems to last longer than the T-9.

Bob in NJ.

Re: Table saw and Jointer Table - cleaning/preserving

#7

Jesper, Denmark

Re: Table saw and Jointer Table - cleaning/preserv

Jesper, Denmark

What the others said, especially stay away from anything with silicone in it. That includes car type waxes.

It has the potential to ruin any subsequent finish work.

Re: Table saw and Jointer Table - cleaning/preserving

#8

Re: Table saw and Jointer Table - cleaning/preserv *LINK*

Jim Dillon

David,

I've had luck with Klingspor's Sandflex Blocks plus WD-40, followed by a thin coat of Renaissance wax.

Jim


Klingspor Sandflex Blocks

Re: Table saw and Jointer Table - cleaning/preserving

#9

Re: Table saw and Jointer Table - cleaning/preserv *LINK*

Jesse Cloud

Paste wax works fine. The spray on products are ok, but have some pretty nasty stuff in them, be sure your room is ventilated well.

This stuff is really cool. Goes on easier than paste wax and is nontoxic, even approved for use on food handling equipment. No silicone. A little expensive, but a can will last a lonnggg time.


Slip-it

Re: Table saw and Jointer Table - cleaning/preserving

#10

Re: Table saw and Jointer Table - cleaning/preserv

Dave Bair, Eaton Rapids, MI

I've learned to skip the use of any oil or lubricant except for the paste wax. I get a glob of Johnson's on a grey synthetic pad and scrub the entire iron surface. I wipe off the excess wax with a shop towel, let the residue dry and buff it out with 0000 steel wool.

Re: Table saw and Jointer Table - cleaning/preserving

#11

Re: Table saw and Jointer Table - cleaning/preserv

Bill White

David, glad to hear from ya. It HAS been a while.

Grey pad, paste wax, buff, done. Now remember that a saw top is not a mirror as some would have you to think.

Bill

Re: Table saw and Jointer Table - cleaning/preserving

#12

That Is Something To Reflect On, Bill

George@Colonel's Workshop-Havertown PA