Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Really straight dry wood

Posts

Really straight dry wood

#1

Really straight dry wood

eliot d

OK. so here's my issue: I like to make my own picture frames, about 20 x 26 inches and I don't want to make a big production about it. So I get a nice finished board from nowhere special and rip it into strips about 3/4 x 1 1/4 inches. Then cut to length, rabbit and miter. Last one was red oak. The problem is that I can't count on the ripped strips not to bend a little, which screws up the frame ending up square after mitering. What I'd prefer not to do is cut oversize and straighten out later. I was thinking that there must be some kind of wood (other than plywood or MDF) that will retain the straight shape the best. Any ideas?

Re: Really straight dry wood

#2

Any wood that is dried properly

Bill Tindall

There are some rare cases of properly dried wood that has tension in it, but for the most part you problem stems from wood dried too fast for the species being dried. Oak needs to be dried the slowest of any domestic wood, so it follows that stress is most likely to show up in oak. Walnut, cheery, mahogany and poplar can be dried more quickly so it follows that these species will be less apt to have drying stress. If you buy from a reputable supplier the lumber should be fine most of the time. There will be the occasional stressful piece either because it grew that way or it was wetter than the rest of the pack that went into the kiln. Beware of boards that have both sapwood and heartwood as they can be stressed due to the differential shrinkage of these parts.

Re: Really straight dry wood

#3

Lee Grindinger

Realistically

Lee Grindinger

Realistically you won't find this perfect lumber of your dreams. Plan on rough ripping and straightening after a bit of time to let the wood work out it's new configuration. Cutting to rough length first will help minimize losses.

Lee

Re: Really straight dry wood

#4

ebd

Re: Realistically

ebd

Realistically, I've never had to rough cut any lumber to get perfect mitres. Of course I use a self built sled that is dead nuts right on and the lumber has been in my shop for years.

Re: Really straight dry wood

#5

Dale Lenz

Would also add...

Dale Lenz

to the above information is to bring the new lumber into your shop and let the moisture content adjust. Put the new lumber some place to where it will get air to all four sides for 2-3 weeks. While working the picture frames don't let the pieces lay flat on your work bench over night, lean them against the wall or something similar. Ninety-five percent of all wood movement is due to moisture loss/gain, the other five percent is due to what Bill stated about reaction wood from the tree. Square wood laid on a flat surface will allow moisture to adjust quicker on the three exposed sides causing a moisture gradient problem due to the difference between the three sides and the bottom side. Hope this makes sense.

Good luck, we all have experienced what you are going though.

Re: Really straight dry wood

#6

Re: Realistically

Lee Schierer McKean, PA

I am of the school that properly dried and acclimated lumber will generally stay straight.. The wood I get from my supplier rarely has any problems so nearly all my material comes from there. it costs more than buying rough stock and it has all been kiln dried. however, I can start a project rihgt away and don't have bags of shavings to get rid of.

I refuse to buy hardwood from the borgs because their handling and storage is hap hazard. Lumber needs time to adjust so when you cut strips from thick or rough stock, cut it oversize, let it set a few days before final sizing.

Lee

Re: Really straight dry wood

#7

Few Suggestions

Mark Mandell - Gone Round In Jersey

First - Consider an alternative to Red Oak; white oak is far more stable. Look for more stable species for your frames.

Second - We can all surmise as to what "should" happen with "properly" dried wood, but the net net is that you're working with an organic material that is not uniform. Compression wood can crop up in a board that looks dead flat and straight. "Planning on the squirrels," rather than getting into a bitch session with the lumber yard, is a better and far less stressful course of action. If you're like most of us, you don't have a wide choice of hardwood suppliers within non-serious driving distance. Most guys will stand behind their product, but don't overdo the complaint department; the next time you have an issue, they may not pick up the phone.

Third - Leave yourself extra material in the buying and cutting. A bit more sawdust in the collector is way cheaper than shorts and rejects in the scrap bin. But remember, the stuff does grow on trees ;)

Re: Really straight dry wood

#8

Re: Would also add...

del schisler

check your saw blade Is it the same as always? May have to change to less teeth on blade Maybe it is heating up the wood and making it move I notice that sometime's when i cut some oak it will tend to try and go back togother when cutting I have a good blade Walnut also does that to Mite be cutting to fast I know you done this hunderd's of times Try less teeth on a blade and see if it moves when you cut or after you cut ? All the boards do this or just a few ? look at the ones that twist and see the grain and look at the ones don't twist and see if their is a big difference in the way the grain is running my 2 cents

Re: Really straight dry wood

#9

Re: Really straight dry wood

DouginDenver

I make lots of picture frames. Whether wood stays dead straight just depends, so I always cut a bit oversize to allow for it. I just built a frame from jatoba, and that stuff has a mind of its own. But a few years ago I started to build a desk from paduak but never got around to finshing it yet, but that stuff is so stable and dead flat that to this day I use one of the leg blanks as a straigtedge for my veneer saw when making seams in veneer. Now that's straight.