Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

(OT) removing bolts with heat

Posts

(OT) removing bolts with heat

#1

Moses Yoder

(OT) removing bolts with heat

Moses Yoder

I am working on an exhaust system on my car tomorrow and can't remember whether you heat the bolt or the area surrounding the bolt when you are using a torch to remove bolts. There is a plate on the back of the catalytic converter where the exhaust is attached with bolts threaded into the plate. I can just imagine how hard those bolts are rusted into that plate and I don't want to ruin my catalytic converter. Another question, is ther any suggestion for putting something on the clamps and bolts for the exhaust system that will keep them from rusting together?

Re: (OT) removing bolts with heat

#2

Re: (OT) removing bolts with heat

Andy Wright - Allen, TX

two suggestions:

1) spray some "penetrating oil" on the bolts tonight and let it sit overnight. That will help loosen up rusted bolts


2) use an "anti-seize" compound to install the new bolts.


You can buy both at any car parts store

Re: (OT) removing bolts with heat

#3

Re: (OT) removing bolts with heat

DouginDenver

Heat expands metal, so you want to heat what the bolt threads into and heat the bolt itself as little as possible. If you heat just the bolt, it will get even tighter.

Re: (OT) removing bolts with heat

#4

Re: (OT) removing bolts with heat

J MOHNIKE

IF THE OTHERS DO NOT WORK FOR YOU, YOU CAN TRY HEATING THE BOLT AND WHILE IT IS STILL HOT POUR ON SOME BRAKE FLUID. MY FATHER INLAW TAUGHT ME THIS YEARS AGO, WHEN I WAS TRYING TO REMOVE A BED KNIFE FROM A LAWN MOWER. EVERYTHING ELESE HAD FAILED BUT HIS TRICK WORKED.

GOOD LUCK

JOE

Re: (OT) removing bolts with heat

#5

Re: (OT) removing bolts with heat

Kneale Brownson..Back enjoying CO snow

Works as a good rusty bolt loosener.

Second the application of antiseize on the threads when reassembled. On an exhaust system, I'd use the higher-temperature rated copper colored antiseize.

Re: (OT) removing bolts with heat

#6

One caution on the antiseize

Bill Houghton, Sebastopol, CA

If your car's exhaust system moves around a lot (you can tell by how they've designed the exhaust hangers - if they're clearly designed for lots of movement, that's your hint), antiseize can encourage spontaneous loosening. Check the tightness of the system after a month or two.

Bill, still touchy on the subject, after years with a Volvo that could shake loose the exhaust in a drive downtown

Re: (OT) removing bolts with heat

#7

Re: (OT) removing bolts with heat

Neal in San Jose

I'd recommend using a six point socket if you can. You can put more torque on it without distorting the head of the bolt. A 12 point can work, but if you really lean on the socket, it can deform the head and then your are hosed. I had to do that to get the flywheel bolts off of an old Ford after someone had tried to get them off with a Crescent wrench - what a pain.

Re: (OT) removing bolts with heat

#8

Shouldn't matter

John in NM

The steel will equilibrate fast enough for it not to matter a lot which you heat. The reason it works is that as both expand with heating, the hole gets bigger "faster" than the bolt because it has a larger radius. There's a great physics class demonstration that shows this, using a sphere and a ring on handles. The sphere won't pass through the ring until the ring is heated sufficiently. But heat them both the same amount, and the sphere will still pass through the ring.

Of course, I've usually had to resort to a cold chisel and new bolts when I've been doing this job :D

Re: (OT) removing bolts with heat

#9

Re: Shouldn't matter

john lucas

I agree John. I've used all of above to get bolts off an exhaust. Now I just buy all new bolts and hangers when I buy the parts. It's faster and less of a hassel. It's worth the money for me.

Re: (OT) removing bolts with heat

#10

Dave

Re: (OT) removing bolts with heat

dave

Hi, I have lots of experience on this so here goes:

if its a nut and bolt, heat the nut, try to avoid heating the bolt, if using oxy acetylene, then use as small a tip as you have for focused heat, get to dull red, then go w/ 6 sided socket and unscrew,

if a bolt into a cat converter, the heat flange around bolt then back out, keep a garden hose under car, w/ nozzle in case of fire. have fun1

Re: (OT) removing bolts with heat

#11

Dale Lenz

My method...

Dale Lenz

is take the vehicle to a muffler shop and have them cut the bolts, nuts and hangers off with a torch. I've always hated working on exhaust systems on cars!! In H.S.auto-mech class, when the teacher ask for volunteer(s) on exhaust sytems, everyone got busy real quick like working on something!

Re: (OT) removing bolts with heat

#12

Re: (OT) removing bolts with heat

Charles in Mtl.

Hey joe,

Not to hijack this thread but i used your method to remove some stuck screws holding the rotor in place on my car and it worked like a charm....except i used WD 40 to cool the screw after heating it. :D

thanks,

chuck

Re: (OT) removing bolts with heat

#13

Re: (OT) removing bolts with heat

Bob Boettcher

A friend sent me the following information on RUST BUSTER solutions. Very interesting. I have not tried it yet, but intend to when the need arises.

RUST BUSTERS

From the April/May 2007 edition of Machinist�s Workshop. They tested various penetrating oils and measured the force required to loosen rusty test devices.

The best one was a 50/50 mix of Automatic Transmission Fluid and Acetone!!!!!

Penetrating oil Avg. Load Price per fluid ounce

None 516 pounds 0

WD-40 238 pounds $0.25

PB Blaster 214 pounds $0.35

Liquid Wrench 127 pounds $0.21

Kano Kroil 106 pounds $0.75

ATF-Acetone 53 pounds $0.10

Hope this helps someone,

Bob

Re: (OT) removing bolts with heat

#14

Ellis Walentine

Amazing!

Ellis Walentine

What a breakthrough that is! I'll keep that one in mind for sure. In fact, I'll make up a little can of the mix next time I get to the shop. Thanks!

Ellis

Re: (OT) removing bolts with heat

#15

Re: (OT) removing bolts with ATF/acetone

paul in AZ

The 50:50 mix of automatic transmission fluid/acetone is a wonderful rust penetrant. Given a bit of time to work it seldom needs a repeat application. A buddy who restores antique cars uses this for the more stubborn bolts as he dismantles rusted car parts. For a casual user neither ATF or acetone is something many want to keep on hand so that is one limitation. I keep Liquid Wrench around for my sporadic use. All too many will grab the one can most have on the shelf -WD40- which is not a good penetrant at all but is a water dispersal material.