Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Fastening flashing on wood?

Posts

Fastening flashing on wood?

#1

JL

Fastening flashing on wood?

JL

I'm building these entry "fences" for a friend. I am building them out of cedar.

They will be sitting on mulch - so they will be down in the wet stuff. I was contemplating putting some aluminum flashing on the places where the cedar will contact the mulch or ground. I am painting the cedar with exterior paint. I am priming the cedar first.

The larger column will be fastened to a pressure treated post that will have its lower portion sunk into the ground (with concrete).

Should I use flashing on the bottom of the cedar columns to protect against moisture or should I just seal it well?

TIA

Re: Fastening flashing on wood?

#2

Re: Fastening flashing on wood?

Joseph Mulherin, Sr

JL, my suggestions are these: you do not need any flashings on anything.

When you dig the post hole go down to about 24", put in about 6" of gravel below the post for water to drain away, install the post and dry fill the concrete, then wet down the post hole with water until the area is fully damp. Then mix up some wet concrete and make a sloping of it like a flashing would have to drain away any accumulating moisture. And cedar does not need any kind of flashings either, unless you want it to have a nice looking appearance. And painting is not needed either on cedar or treated lumber unless is is for appearance.

Re: Fastening flashing on wood?

#3

In Short . . No

Mark Mandell - Gone Round In Jersey

You want the wood to drain and dry. Putting flashing on the bottom with act to hold water in the wood, fostering the rot. Same answer for sealer. You want the end grain left "open" so that the "straws" can release their moisture easily.

For the same reason, you should expect the ends of the cedar boards that touch, let along penetrate, the mulch to rot off in several years. Cedar is nicely bug resistant (for everything but carpenter bees), but water will rot it from the inside out. Leaving a space between the ground and the fencing will add to the boards' life. If you need to block that gap, run a width of hardware cloth of chicken wire along the bottom.

Re: Fastening flashing on wood?

#4

Concur

Bill Houghton, Sebastopol, CA

Flashing is properly used where it will encourage water to drain OFF things, like roofs.

Re: Fastening flashing on wood?

#5

Re: Fastening flashing on wood?

paul in AZ

Why not consider fence post anchors that keep the wood above ground level? The 2 kinds I've seen are an anchor atop a 2 or 3 foot spike which is pounded into the ground and the type with a U-shaped anchor attached to a rod that is embedded in concrete. Just bolt the posts into the anchor.

If nothing else these will make replacing the posts a piece of cake years down the road.

Re: Fastening flashing on wood?

#6

Re: Fastening flashing on wood?

Barry Irby

JL. Cedar is not very decay resistant in contact with the earth. You should raise it off the ground if you can.

Wood rots because it gets wet and stays wet. If it dries quickly and does not stay wet for long it will last a long time. It it stays wet and warm, it rots much more quickly.

Installing flashing is more likely to retard drying and accelerate decay than to prevent it. Water will find its way in and the flashing will keep it from drying.

Also, I would recommend you set the posts on a base of gravel in the holes as suggested by others. But, rather than set them in concrete, fill the holes with gravel and tamp it. Use gravel rather than rounded river stone. Sharp angular stones will lock up nicely and hold the posts securely and yet drain and dry quickly. You want something like No. 5's or No. 57's, not crusher run.

Concrete works against you. It sets and then holds water against the post. If the post were dry when installed, it may swell with the water and brust the concrete.

Re: Fastening flashing on wood?

#7

Jason Roehl in Lafayette, IN

Or...

Jason Roehl in Lafayette, IN

...since he mentioned using treated posts, more likely they will be wet when the concrete is poured, then shrink away from the concrete later on, leaving a neat little gap between the post and the concrete to hold water and help rot whatever wood is handy.

Jason

Re: Fastening flashing on wood?

#8

Wood rot

Tom Dunlap

The decay micro-organisms like damp conditions. Keeping the wood dry or saturated will keep the wood from rotting. The rougish-fungiis that rot wood are aerobic and need oxygen. Wood that is in water will not rot.

Setting the post in rocks would be a good choice or making a concrete footing with a connector like others suggested will give you a better footing.

Re: Fastening flashing on wood?

#9

JL

Thanks - no flashing then..

JL

I'll put the PT posts in concrete with gravel - or maybe just gravel then. We've got enough clay around here to keep things locked up.

Re: Fastening flashing on wood?

#10

PT Posts

Mark Mandell - Gone Round In Jersey

The sales pitch on treated SYP says "20 years" for ground contact. You can make that 35 or better by coating the buried part with a good slather of roofing tar. Did my deck with 4x4's set on concrete pads below the frost line with the 24" holes filled with 1-1/2" blue stone compacted with a jumping jack. 20 years and not a sign of rot or weakness.

Re: Fastening flashing on wood?

#11

Addendum

Bill Houghton, Sebastopol, CA

If you need to cut the post, don't put the cut end in the ground. Most of the pressure treated wood is treated an inch or two into the wood, with the center remaining vulnerable. If you put that vulnerable end in the ground, you'll wind up with a hollow post right quick.

And, if you do need to cut it and put the top end up in the air, slather it with copper or zinc napthenate. Zinc smells better, but I have not yet decided if I trust it. Locally, only the professional paint stores are carrying the copper napthenate. Either product, the end grain will soak up huge quantities of the stuff. Paint it on, then again; let that dry; repeat a few times.

Bill, testifying from experience