Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Steam Bending - Propane BTU Rqmts

Posts

Steam Bending - Propane BTU Rqmts

#1

Steam Bending - Propane BTU Rqmts

Paul Leuba

I am assembling a small steam bending set up for the back bows and arms of windsor chairs. The question relates to how much BTU output is needed for the propane burner to boil 3 - 4 gallons of water in a reasonable amount of time (10 mins or so).

The choices available for internet purchase range from a burner capable of 55,000 BTU/hour (10 PSI regulator) and one capable of 185,000 BTU/hour (20 PSI regulator).

The burners will be used outside. I do not want to purchase one to weak to build and sustain the heat necessary to sustain steam for the required 15 + minutes, and, at the same time, I do not want to purchase a burner much bigger than necessary.

Any advice on this would be appreciated.

Paul in Hunt Valley, MD

Re: Steam Bending - Propane BTU Rqmts

#2

Re: Steam Bending - Propane BTU Rqmts

del schisler

here a google search Look at them their is some that will get the right btu for the boil

http://www.google.com/search?hl=en&source=hp&ie=ISO-8859-1&q=+55%2C000+BTU%2Fhour+to+boil+water

Re: Steam Bending - Propane BTU Rqmts

#3

Re: Steam Bending - Propane BTU Rqmts

Paul Leuba

Thanks, Del!

Based on the formula on the web site, 3 gallons of water should boil in 10 - 12 minutes with a 55,000 BTU/hour burner delivering heat to the pot at a 50% efficiency.

That get's me close to where I need to be.

Paul in Hunt Valley, MD

Re: Steam Bending - Propane BTU Rqmts

#4

Jim DeLaney, Austintown, Ohio

Re: Steam Bending - Propane BTU Rqmts

Jim DeLaney, Austintown, Ohio

I don't know the BTU output, but I use a burner intended for turkey frying. I got it cheap - like $5.00 at a garage sale.

My water container is a BRAND NEW, NEVER USED 5 gallon gas can. I put about three gallons or so of water in it, and it boils in about 6~6 minutes. I run an automobile radiator hose from the can to the steam chamber, which is either a piece of 6" PVC pipe or a box made from 1 X 8's, depending on the size of what I'm steaming.

Jim D.

Re: Steam Bending - Propane BTU Rqmts

#5

BTU's unknown

Lee Schierer McKean, PA

When I steam bet some cherry a number of years ago, I used a gallon paint thinner type can and a Coleman white gas type stove. It produced lots of steam for over an hour and still had water to spare.

Lee

Re: Steam Bending - Propane BTU Rqmts

#6

Re: Steam Bending - Alternative

Mark Mandell - Gone Round In Jersey

I used an electric hot plate, a 2 quart tea kettle, and a drain that returns condensate to the kettle. Set-up will steam nicely for several hours with box (8"x8"x48") temp at 212� and no additional water needed. Kettle connected to the box with a length of 1-1/4 aluminum vacuum cleaner wand. The condensate return was 1/4" copper tubing.

Re: Steam Bending - Propane BTU Rqmts

#7

Jason Roehl in Lafayette, IN

Good description, Lee.

Jason Roehl in Lafayette, IN

I think the setup the OP described is probably way overkill, and a waste of lots of energy. Remember that (gaseous) steam is roughly 1000 times less dense than (liquid) water. So 3-4 gallons of water could produce around 3000-4000 gallons of steam. That's a LOT of steam.

For comparison, think about the chafer dishes you see on food buffet lines. They work best with only a very small amount of water in them (~1/8"), and just a small can or two of sterno underneath. They'll produce steam that way for quite some time.

I'd look at building a system that uses something more on the order of a quart or half-gallon of water. It will heat much more quickly with a much smaller burner setup, and still produce steam for plenty of time.

Jason

Re: Steam Bending - Propane BTU Rqmts

#8

Re: Steam Bending - Propane BTU Rqmts

Paul Leuba

Thanks all for the informative feedback. It appears that a condensate recovery system with a modest size water resevoir is a good setup that can be heated with a small heat source.

Paul in Hunt Valley, MD

Re: Steam Bending - Propane BTU Rqmts

#9

Re: Condensate

Mark Mandell - Gone Round In Jersey

Make your steam box slanted with a couple of small holes at the low end for the drain - you need a vent in order to keep steam going into the box anyway. The holes drip into a metal funnel or cup which, in turn, drains back to the kettle. This is, after all, a low pressure operation.

Reminder: general rule is 1 hour per 3/4" of stock after the box reaches 212� depending on the species. White oak is regarded as one of the best. Sweet fruit woods like cherry can be very difficult.

Tip: Make the interior dimension of the steam box at least 25% wider than your widest stock. This improves circulation and gives more even heating. Also, the wood does swell and can literally get stuck DAMHIKT ;)

Re: Steam Bending - Propane BTU Rqmts

#10

JL

A larger pot is a good pot...

JL

I don't believe I've ever measured the BTU output of my burner. Turkey frier burners are good and so is this one (two burner portable with removable legs).


This particular steam box is 8' long. I use it to bend Windsor settee hoops as well as chair hoops (and crests, etc.). I like a larger pot because I can rest the steam box on the pot - that way I don't need a stand.

Re: Steam Bending - Propane BTU Rqmts

#11

You have lots to learn

Keith Newton----Little Rock, Arkansas

It is not just a matter of having wood in the presence of steam. The goal is to get the wood temperature up to 210� all the way to the middle which allows the lignin to soften. If the core doesn't make it up to this level, failure is most likely.

The larger the chamber, and quantity of wood, the more BTUs needed. Also, since the OP mentioned outside use, the more heat is needed to make up for loss to the outside when it is cold. Insulation will help.

My first attempts at steaming back in the seventies, over a camp stove failed due to lack of enough steam.

I don't know how many BTUs my burner provides, but my big canning pressure pressure cooker holds ~ 5 gallons, and I use about one gallon per hour, which has been working pretty good for my projects. The only downside to more steam than needed is of course more energy cost, which is cheap compared to the time and energy lost, and frustration when there isn't enough.