Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

O.T.:,,,free GFCI cord

Posts

O.T.:,,,free GFCI cord

#1

O.T.:,,,free GFCI cord

fixitgood

Disclaimer:I am not a licensed electrician. NEMA 1

All NEMA 1 devices are two-wire non-grounding devices (hot-neutral) rated for

125 V maximum. NEMA 1-15P plugs have two parallel flat blades, 1⁄4 inches (6.35

mm) wide, 0.06 inches (1.524 mm) thick, 5/8�23/32 inches (15.875�18.256 mm)

long, and spaced 1⁄2 inches (12.7 mm) apart, and are commonly found on household

lamps and consumer electronics such as clocks and radios. ... Plugs may be and

receptacles must be (since 1948) polarized to preserve the identity of the

neutral conductor;

==> the blade connected to NEUTRAL (ground,low side) will be WIDER (5/16

in/7.938 mm) than the other,<===

and polarized sockets will only accept a polarized plug in the correct

orientation.

http://en.wikipedia.org/wiki/NEMA_connector

The NEUTRAL (ground side) will be silver on a receptacle. -- 'High' "hot'

side will be brass or a darker color. - - -On lamp cord 'zip cord' the NEUTRAL

will have ridges on that side and be connected to the wide blade. - - - The

'HOT'(or high) side wire will be smooth and connected to the narrow blade.

'hot side'=black wire=brass screws=narrow blade or prong=smooth side

on lamp cord.

neutral side=white wire=silver screws=wide blade or prong=ridged side

on lamp cord.

http://www.hometips.com/how-it-works/wiring-electrical-outlets.html

O.K. When your hair dryer 'dies' and it has a ground fault circuit

interrupter-

the fat plug with buttons-cut the cord off as close to the dryer as

possible,save it,

install a polarized female cord receptacle-OBSERVING POLARITY-and you have an

extension cord that is GFCI protected and be a little safer.

Re: O.T.:,,,free GFCI cord

#2

Extension cord, yes...

Bill Houghton, Sebastopol, CA

but most of the cords on the hair dryers I've seen have been light gauge. What appliances/tools could usefully be run on such a cord?

Re: O.T.:,,,free GFCI cord

#3

Re: Extension cord, yes...

Chris Hays

O.K. Bill you win. I do not want to argue.Some hair dryers are rated at 1600 watts which is near 15 amps.

Some are more.I found data for appliances but none for tools:

Typical Wattages of Various Appliances

Here are some examples of the range of nameplate wattages for various household appliances:

� Aquarium = 50�1210 Watts

� Clock radio = 10

� Coffee maker = 900�1200

� Clothes washer = 350�500

� Clothes dryer = 1800�5000

� Dishwasher = 1200�2400 (using the drying feature greatly increases energy consumption)

� Dehumidifier = 785

� Electric blanket- Single/Double = 60 / 100

� Fans

o Ceiling = 65�175

o Window = 55�250

o Furnace = 750

o Whole house = 240�750

� Hair dryer = 1200�1875

� Heater (portable) = 750�1500

� Clothes iron = 1000�1800

� Microwave oven = 750�1100

� Personal computer

o CPU - awake / asleep = 120 / 30 or less

o Monitor - awake / asleep = 150 / 30 or less

o Laptop = 50

� Radio (stereo) = 70�400

� Refrigerator (frost-free, 16 cubic feet) = 725

� Televisions (color)

o 19" = 65�110

o 27" = 113

o 36" = 133

o 53"-61" Projection = 170

o Flat screen = 120

� Toaster = 800�1400

� Toaster oven = 1225

� VCR/DVD = 17�21 / 20�25

� Vacuum cleaner = 1000�1440

� Water heater (40 gallon) = 4500�5500

� Water pump (deep well) = 250�1100

� Water bed (with heater, no cover) = 120�380

Re: O.T.:,,,free GFCI cord

#4

You're Both Right

Mark Mandell - Gone Round In Jersey

Here's why, Chris.

The current carrying capacity of the cord, and thus the "required" size, is a function of the length of the conductors. You hair dryer is 1500 watts, but it's on a 6 or 8 foot cord which can safely be 18 or 20 gauge wire for 1500 watts at 115v. But when you take that same 1500 watt load and put it 25 or 50 feet away, the resistance factor of the length of the wire goes up substantially which results in current loss to the tool and translates to heat in the wires. Too much heat and the insulation will melt, and your 20 ga. wire will fail. This is why running power tools on too thin a wire is bad for the tool; the motors don't get their full amperage requirement, they don't develop full rpm, and all of this heats them up and degrades the motor windings. It's also why I can run a 3hp 13 amp table saw or planer on a 8 foot 16ga. wire.

I don't put any tool on an extension cord of less that 16 gauge wire, and for anything over 25 feet I only use 12 ga. wire extension cords. Since most of the time that I have a power tool on an extension cord it's outside, the GFCI issue is taken care of by the house circuitry since all outside circuits must be GFCI.

I do, however, save cords from old appliances and tools, in case I need a molded 3-prong plug :D Which reminds me, it's time to throw some away.

Re: O.T.:,,,free GFCI cord

#5

Interesting idea for small outdoor light

Joe Pack

Might be a good idea for a small outdoor light display. I'm always worried about something shorting out.

Thanks for the tip.

Re: O.T.:,,,free GFCI cord

#6

I may be a little over-sensitive on this subject

Bill Houghton, Sebastopol, CA

When we moved into our house 37 years ago, we found some circuits done with lamp cord; and the incoming "service feed" for the whole house was 12 gauge. By some miracle, there was never an electrical fire before I was able to rewire the whole house in the 90's; but I've thought, more than once, that we were some lucky folks.

It's really easy to overload a cord if you don't do the math to determine what the load is. I've seen people running things on cords that were seriously undersized for the application. I no longer buy extension cords except in 12 gauge, unless I know for sure that they'll never be used for any but light loads.

I agree that this cord would be helpful for people whose houses don't have GFCI outlets and who, for whatever reason (renting, uneasy about doing electrical work and have no money, etc.), aren't able to install them. I suggest that, rather than treating them as extension cords, people should cut the cord short enough to treat them rather as portable GFCIs for the kind of low-wattage uses your follow up post suggested.

I didn't mean my earlier post as an argument, except in the intellectual sense of bringing our individual experiences and knowledge together to arrive at the best answer.