Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

new use for Carbide..... OT

Posts

new use for Carbide..... OT

#1

new use for Carbide..... OT

Barry Irby

My son got married recently. He and the wife went to get wedding bands. He complained that every ring he ever had been damaged in his work. (Horticulture) The jeweler presented him with an interesting solution. A band made of Carbide. Beautifully polished sort of silvery black. Nearly indestructible. Less expensive than gold. So far he is pleased. Could be a new use for those old router bits.

Re: new use for Carbide..... OT

#2

Now if we could just get $1000 an ounce for them

john lucas

Re: new use for Carbide..... OT

#3

Surprising

John in NM

I would have guessed that carbide would be too brittle for a ring.

Re: new use for Carbide..... OT

#4

Re: Surprising

Marv

John,

Probably not the same composition as the carbide we use. It is tough stuff though. Consider the thin cutting edge of most all cutting bits, milling cutters, drills, etc.

Marv

Re: new use for Carbide..... OT

#5

David Barnett

Tungsten carbide jewelry is everywhere these days  *LINK*

David Barnett


Tungsten carbide rings

Re: new use for Carbide..... OT

#6

Re: Surprising

John in NM

I think the advent of carbide jewelry likely has more to do with a combination of novelty and improvements in cutting/polishing technology than any really suitable material properties. Surgical stainless steel would make a much more practical ring in terms of durability, though its not used much, being a cheap material.

Re: new use for Carbide..... OT

#7

Re: new use for Carbide..... OT

Andy Wright - Allen, TX

I bought a tungsten carbide wedding band about six months ago, and am amazed at its durability. My wedding bands usually take a beating from the day I buy them until the day I lose them, but this thing has NO SCRATCHES after six months (and I wear it to work in the shop, work on cars, do yardwork, etc)

When I bought it, the jeweler actually ran a file across the ring to show how resistent it is to scratching. It was also relatively inexpensive ($199), but it can't be engraved without sending it to a laser engraver, and it can't be resized or melted down (I am sure that they can be worked, but its nothing like gold where a jeweler can modify it in their shop)


Re: new use for Carbide..... OT

#8

One word of caution...

John E in SC

Chances of this happening are very slim, but just a word of caution here. Whenever I see rings made of "new" materials like this, the first thing I think of is how hard would it be to cut it off? I'm a family doc, and have had numerous times over the years where I've had to cut off someone's ring due to swelling or an injury to the finger. I know the cutter I have wouldn't touch carbide. I can't imagine what you would have to do to get it off. (Haven't seen diamond-tipped ring cutters yet!) Just something to think about. Rare, but it happens.

Re: new use for Carbide..... OT

#9

David Barnett

Good point, but easy enough...  *LINK*

David Barnett

You can also kerf with a rotary tool and diamond disk, then shatter with a blunted steel wedge.


Tungsten carbide ring removal

Re: new use for Carbide..... OT

#10

NO! NO!  Don't wear rings doing that kind of work

Bill Houghton, Sebastopol, CA

It's a pretty ring, but you've now guaranteed that your finger is the weak link if the ring gets caught in something while you're working. Knowing that your wedding ring will stay pretty forever, just like your love for your bride is very nice; but...

In a Fine Woodworking article on shop safety some years back, the physician writer mentioned the medical term for what happens to the flesh on your finger when a ring gets caught in the machinery: "de-gloving." The image this brought up creeped me out so much I immediately stopped wearing my wedding ring while doing physical work.

I'm not sure what the electrical conductivity of carbide is, but, on a car, there's also the possibility of spot-welding the ring and a wrench together if you're working on electrical components.

Find a good place on your dresser to put the ring when you're using anything that involves a tool or fast-moving machinery. Put it there every time - before you go out of the house. If your sweetie asks why you're not wearing your ring, tell her you want all your fingers for holding her hand with.

Re: new use for Carbide..... OT

#11

Re: Good point, but easy enough...

John E in SC

Good info. I knew titanium could be cut - just takes a lot longer. Guess we'll have to add a pair of vice grips to the "surgical" tools just in case!

Re: new use for Carbide..... OT

#12

I know I should take it off...

Andy Wright - Allen, TX

I know I should take it off, but that is how I lost my last two wedding bands. I think it may actually be less painful to lose a finger than incur the wrath of my wife for losing ANOTHER wedding band ;)

Re: new use for Carbide..... OT

#13

steel not nearly as durable

Chris Friesen

I've got an engineering degree, and hence a steel ring. It's definitely scratched up from daily wear. I suspect a carbide ring would be much more durable than steel.