Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Advice on Pin Gun?

Posts

Advice on Pin Gun?

#1

Advice on Pin Gun?

Barry Irby

I have been wanting a pin gun for a while. One that shoots the very slender pins. (23 Ga.?) All of the guns I have now are Senco. Any reason not to buy a Senco pin gun? Is it important to go for the long ones? I have no particular use for one, would just like to ad it to the arsenal.

Re: Advice on Pin Gun?

#2

Re: Advice on Pin Gun?

doug f, san clemente, ca

Barry - the one I have and use a lot is a Grex; pricey but just about bullet-proof. Mine shoots lengths up to 2", but I find I rarely use much over 3/4"-1". Longer than that is usually heavier material and my 18 ga. is the tool of choice.

I'm sure you're going to get the usual array of favorites and failures, but a gun that resists jamming is my number one criterion.

Have fun with your new toy..., eh,... tool.

Doug

Re: Advice on Pin Gun?

#3

Re: Advice on Pin Gun?

Jon Weisenbach

My first was an Accuset by Senco. Total pos! jammed constantly, even after replacing drive pin via warranty. Second call to c/s they said send it back and they replaced with the Senco and been trouble free for 5 years and counting. Their price is good and no problem getting pins via the web. Not capable of the longest pins but I personally have never had a need for anything longer than 1"

Re: Advice on Pin Gun?

#4

Re: Advice on Pin Gun?

Christopher Fitch Memphis

I have a Cadex. I like it alot...well made and works well for me.

Re: Advice on Pin Gun?

#5

Re: Advice on Pin Gun?

FredD

I will echo Jon on the Senco, I have had mine since about 1974 , never a problem , shoots three lengths, adjustment for each and while everybody has a favorite , I stick with Senco because of their reliability and longevity.

I still have boxes of the original pins made in Italy for Senco

FredD

Re: Advice on Pin Gun?

#6

I second the Grex

Scott in Montana

I have the 1 3/8" model and have nothing bad to say about it. I use it constantly. 3/4" to 1 1/4" mostly. I've never owned the Senco.

Scott in Montana

Re: Advice on Pin Gun?

#7

Grex Here Too

David Yoho

I researched pin nailers before purchasing my Grex. I shoot between 3/4" to 1 1/4" lengths the most. Love the feel and precision. The cost is higher than others but well worth it in my opinion.

David

Re: Advice on Pin Gun?

#8

Re: Advice on Pin Gun?

Doug Ridley

I know I'm in the minority here but for occaisional use only I bought a 23 guage pinner from Harbor Freight for $25.00 and it has worked fine. Have used it quite a bit and had no problems with it. I am not much of a HF fan but a few of their things seem to be okay.

Re: Advice on Pin Gun?

#9

I'll second that.

Al Goldstein

Re: Advice on Pin Gun?

#10

Re: Advice on Pin Gun?

Andy Wright - Allen, TX

I have the Senco and I have never had a problem with it.

Very convenient for holding small pieces of trim, etc. in place while the glue is drying. If you use it in woods with grain like oak or ash you dont even need to fill the nail holes (they just disappear into the grain)

Re: Advice on Pin Gun?

#11

Re: Advice on Pin Gun?

Jorge Casta�eda

Barry,

My brad nailer is a senco and works fine so far, but I head Senco is going out of busines or was bought out by annother company, I also have a Senco Framing gun, having trouble to find nails for it.

All my other nail guns are Hitachi and I love every one, take a look at them.

Re: Advice on Pin Gun?

#12

Mine Works Well, Also

George@Colonel's Workshop-Havertown PA