Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

production picture surrounds

Posts

production picture surrounds

#1

production picture surrounds

eliot d

If I'm making one picture frame, I do all the measuring and cutting and then use four corner clamps to glue it together. So far so good. But suppose I want to make a bunch of them -- say ten -- and I don't want to go through ten glue ups in sequence. One way would be to put the glue up in the clamps, nail in some brads at each corner, take the frame out, and start over with the next frame, and so on. that wouldn't be too bad. Now the question: suppose I don't like using brads or any metal. Is there a kind of production method that won't take forever that doesn't rely on metallic stuff? I've used wooden splines, but I can't see a reasonable way to use them in this kind of quasi-production approach.

Re: production picture surrounds

#2

I edited the title so it would work

Dan Donaldson

For some reason, if the word "frames" is in the title, clicking on the message just returns you to the index. I changed the word in the title to "surrounds", which is kind of strange, but it lets people read the message.

Re: production picture surrounds

#3

Re: production picture surrounds

Gary Smyth

I've used toothpicks instead of brads. The hole is predrilled and the picks driven in. At least one each side. Snapped off on outside where exposed. Wood putty close to wood color covers the holes. Finsh hides it more. If you aren't using them for mirrors or extra heavy stuff they will hold for at least 20 years and going strong..

Re: production picture surrounds

#4

Re: production picture surrounds

FredD

Eliot,

I have tried a bunch of ways to speed up frame assembly and when Gel form Cryanocrylate glue came on the market , the problem was solved.

For instance I make Wainscot from time to time and the one in our home has over a hundred frame joints for the panel inserts, the glue has never failed me.

You can get a large tube of it in any Hobby shop.

Also get a bottle of of accelerator and put a heavy coat of gel on side of the miter and shoot a spray of accelerator on the other side and press together for about five seconds.

Do this on a sheet of waxed paper and test run the way you will hold the joint closed, it will happen fast ,so be sure that the fit is what you want.

Just in case you need to free a finger, keep a pint can of Acetone handy ;-))

FredD

Re: production picture surrounds

#5

Re: I edited the title so it would work

eliot d

Thanks Dan. You're right; when I had the word,'frame' in the title, no text appeared. So thanks again.

Re: production picture surrounds

#6

Re: production picture surrounds

eliot d

Thanks to both Gary and Fred. Of course, I know about super glue. I have a slight problem about it for a picture surround (picture frame) because I fear that it will grab more or less instantly, and if the miter joint isn't lined up perfectly, then I'd be out of luck. (Perhaps, though, I could line up the joint first and flow thin supper glue into the joint followed up with a spray of accelerator.)

Re: production picture surrounds

#7

Re: production picture surrounds

eliot d

I'm going to try this method. I might modify it by using something a bit larger than a toothpick. But the method seems perfect. It's strange that I had this kind of "idea fix" that a thin holding "tenon" had to be a metal brad. Of course, why not what amounts to a thin wooden dowel? And now that I am thinking in this direction, I think I like the idea of using a contrasting wood to show it off instead of hiding it with putty.

Re: production picture surrounds

#8

Bamboo skewers

Bill Houghton, Sebastopol, CA

as for satay or shish-kebab. Your local market probably has them. I've used them for furniture repair, and they worked well. One of the nice parts is that the grain is more or less dead straight, so you get good strength for the cross-section.

Re: production picture surrounds

#9

Re: production picture surrounds

FredD

Eliot,

"thin super glue" is a bad idea for the following reason.

Enough of it will be absorbed by the wood that , the joint will be weak and fail..

The Gel is the way to go and like I recommended to you previously, get your glue and wax paper and accelerator ready and then practice holding the joint until you can smoothly glue one side , accelerate the other side and hold together right the first time.

It is easier then it sounds.

A couple of tips I failed to mentioned are, it improves the fit of the miter if you rub it across a piece of 150 grit paper to get rid of any fuzz and if your frames are a rectangle , glue two sections of a short end to a long side first and then glue the two together, this will allow some flexibility in adjusting the last miter if it needs it.

FredD

Re: production picture surrounds

#10

Re: production picture surrounds

eliot d

Really helpful suggestions. What I may still do, though, is to line up the joint perfectly and use the thin glue with accelerator, which should hold the frame temporally and then use a corner spline jig I made to cut and glue in four splines.This way I can put the frame aside so I can start on the next frame. I'm going to try your thick glue method , too.

Re: production picture surrounds

#11

Another option....

John in NM

though I don't know how available any more. I have a set of those Ulmia spring clamps Garrett Wade used to sell - back when they were in NY and were one of the premium hand tool suppliers. The springs will hold a frame together well, leaving a little dent in the edge that I've cut out for splining or doweling.

You could also try using packing tape to secure the joint while your glue dries. I've not done this often, but it is reputed to work as well as the spring clamps.

Re: production picture surrounds

#12

Re: production picture surrounds

John K Jordan

I just made 10 frames and used this clamp, the best one I've seen:

http://www.woodcraft.com/Product/2003086/433/Picture-Frame-Miter-Clamp.aspx

It comes with extension rods for very large frames and for a few bucks you can get extra corners. One might easily make a few of these clamps with hardwood or birch ply corners and some all-thread rods.

JKJ

Re: production picture surrounds

#13

Re: production picture surrounds

Hamish

You said that you wanted a fast solution without using brads. Almost all of the frames I have bought are usually held together with a couple of staples on the back. Although they are metal, it sounds a quicker method than using wooden brads?

Re: production picture surrounds

#14

Re: production picture surrounds

AZ, Colorado Springs

If aligning the joint is a concern, then use a corner clamp and dry fit the two sides of the frame. Adjust each side until the joint closes tightly. Then, remove only one side, apply the glue and accelerator to the different pieces, then reinsert and clamp the loose side. The same steps as in a non-production assembly, but then after a minute or two (or however quickly the glue sets up) you can remove the clamp.