Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

yet another electrical porblem

Posts

yet another electrical porblem

#1

yet another electrical porblem

Bill Tindall

I have an electric griddle that is powered by a typical controller/thermostat- one long thermal sensing prong and two recessed female receptacles, plus the dial.

One of the female receptacles is overheating, the other is fine. I know it is overheating because the plastic surrounding it is charred and the copper connector part is red like what copper gets when it gets hot. I substituted a second controller and the same side ove- heated as evidenced by the smell of hot Bakelite and discoloration at that receptacle/terminal.

Now electricity goes in one receptacle and out the other so no more current can be flowing in one than the other. But something in the griddle part is causing one of the connections to get hot. Any ideas as to the cause and fix for this problem?

This issue is related to woodworking because I need my buttermilk pan cakes (Alton Brown recipe, oh so good) for energy to plane and saw wood.

Re: yet another electrical porblem

#2

Re: yet another electrical porblem

Dan Donaldson

cases like that are usually caused by a loose or high resistance connection. (in this case, "high" is relative. A half an ohm here could cause a lot of local heating at the currents it is pulling)

Re: yet another electrical porblem

#3

Re: yet another electrical porblem

John K Jordan

As Dan mentioned, reduced conductivity can cause heat which increases resistance which causes more heat which... This can be caused initially by a little dirt or oxidation. High current connectors in hot environments are more susceptible.

Sometimes you can fix the contact problem by disassembling the connector, cleaning the contact, and bending it so it makes a tighter contact. If the primary point of contact is corroded try to fix it to make contact in another place (or two). If not too far gone, spraying electrical contact cleaner into the socket and inserting and removing the plug multiple times may clean it enough. Sometimes it is necessary to replace or fabricate a new connector.

Also, I like to coat conductors with dielectric compound available from any automobile parts store. I put it on almost every connection in home and auto (bulbs, etc.).

JKJ

Re: yet another electrical porblem

#4

Re: yet another electrical porblem

Stuart Johnson

Our B&D had the same problem. First the plug was hard to pull out of the griddle. Then it became next to impossible. It gave up and stopped heating. I forced the plug out and one was very burnt. I didn't even try to fix it, just bought a new one because we do like our Sunday morning pancakes.

Re: yet another electrical porblem

#5

Sounds Like

Mark Mandell - Gone Round In Jersey

A new griddle is in your near future.

I've had several similar appliances over the years and was told that when one side is getting hot like that you have a problem with the connections or "calrod" element(s) inside the pan. FWIW, I was also told "ain't worth fixin' as the element is wearing out."

Re: yet another electrical porblem

#6

what is "dielectric" compound

Bill Tindall

What is this stuff and what does it do? Sounds like something I should know about.

Re: yet another electrical porblem

#7

What to buy?

Bill Tindall

The griddle I have has a thick aluminum surface that heats evenly. Some I have seen are flimsy and I presume would not heat uniformly. Sounds like from the sage advice offered, what I own is doomed and I should cut my losses. What is a good model to replace it that will heat evenly so all my pan cakes are golden brown?

Re: yet another electrical porblem

#8

Re: What to buy?

Stuart Johnson

We just bought another B&D at Target. It is the same model as the last one that lasted a number of years. Model GR100 TY1. It's rather inexpensive and heats very even. I'll just leave the controller plugged in and just wipe the griddle off after each use.

It's funny because I just jumped over to Amazon and it is getting some terrible reviews about uneven heating. I have no idea why I have better results unless it is the heat. I cook my pancakes at around 340. I suppose you could crank it up to 400 and burn them before they had time to cook.

Re: yet another electrical porblem

#9

Re: yet another electrical porblem

Alexandre Grigoriev

Can you post a picture?

It could be a bad contact inside "male" connector overheating the receptacle.

Re: yet another electrical porblem

#10

Re: what is "dielectric" compound

Dan Donaldson

It is basically a grease that is designed to put on electrical connections. It keeps air and moisture away from the connection to keep it sound longer. The grease itself is non-conductive, which is why it is "dialectric".

Re: yet another electrical porblem

#11

similar to but ....

Marv

Bill,

I think it is similar to diarrhea but not exactly the same in function or form.

Dielectric is a measurement of how well a substance will conduct electricity. Copper for example will have better dialectric qualities than wood.

Marv

Re: yet another electrical porblem

#12

Re: similar to but ....

Dan Donaldson

By definition, a dielectric is an insulator. Glass is a dialectric, copper is a conductor ;)

Re: yet another electrical porblem

#13

Re: what is "dielectric" compound

John K Jordan

>...The grease itself is non-conductive

Not related but perhaps interesting: we found out that silicone sealant compound (RTV) is non-conductive only after it has cured. A friend used some to insulate some 110v AC terminals and received a shock when he turned on the device before it had totally cured. Could potentially wipe out some electronics too.

JKJ

Re: yet another electrical porblem

#14

why uncured silicone is conductive

Bill Tindall

During the cure, actually a crosslinking reaction of the silicone polymer, acetic acid is generated, hence the smell. Acetic acid is an good conductor. Not as good as water, but sufficient to carry some current. When the smell is gone it will be an insulator.