Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Router table substrates

Posts

Router table substrates

#1

Router table substrates

DaleLenz

Need to rebuild my router table's surface, attached to right of TS. Over the last 25 years mine has created a slight hump in the middle, probably because I made the frame (between my Beis" rails) to tight. The router's table surface will be about 2'X3', setting on top of a 1x4 wooden frame. The wooden frame will be bolted to the inside of my Beis' TS rails. Plan on putting two of those threaded inserts to secure my router's base to the table. Any suggestion on substrate material, MDO, MDO, etc.(?).

TIA

Re: Router table substrates

#2

Clint Searl

Re: Router table substrates

Clint Searl

I don't know if it would accommodate your situation, but I made a router table top from two layers of 3/4" MDF laminated with an epoxied fiber glass mat, and topped with Formica.

Clint

Re: Router table substrates

#3

Re: Router table substrates

Mark Mandell - Gone Round In Jersey

Made mine with doubled 3/4" MDF. Top is 2x3 with an 18" extension that I made during my "shop furniture" building phase but never used :b . The router (Ryobi 600E) hangs from a 3/8 phenolitic plate that's cut into the top layer with leveling set screws. MDF was edged with 1/2" maple, then over-laminated top and under with mica. Lastly, a miter track was cut into one side with an extruded aluminum track installed for jigs, etc. Dust control is through a plenum box that hangs around the router plus a fence draw port. Stayed dead flat for the last 10 years.

Re: Router table substrates

#4

JL

Please "expand"...

JL

on the fiberglass mat and epoxy lamination. I'd like to know more about this. I could see where it might be useful in certain situations - but I would like to more about properties, costs, etc.

Re: Router table substrates

#5

Clint Searl

Re: Please "expand"...

Clint Searl

I made a sandwich from two pieces of 3/4 MDF by laying a full size piece of woven fiberglass mat on the bottom piece of MDF, saturating the mat with epoxy (I like System3), and laying the top piece of MDF. After it cured, I topped the sandwich with Formica attached with Formica contact cement. The package is heavy, dense, and stable.

Clint

Re: Router table substrates

#6

Doubled 3/4" MDF it is!   Thanks!

DaleLenz

Re: Router table substrates

#7

Re: Doubled 3/4" MDF it is!   Thanks!

Bartstar

Dale,

I made my table from 2 pieces of 3/4 plywood laminated together (with just yellow glue), then edged in Oak, then covered both sides with Formica laminate. I built it about 10 year ago and its still flat after these many years.

Bart

Re: Router table substrates

#8

Re: Doubled 3/4" MDF it is!   Thanks!

mdclor

I used melamine so I didn't have to cover it with Formica.

FWIW,

Merle

Re: Router table substrates

#9

Re: Router table substrates

Barry Irby

I made mine out of two sink cutouts from a cabinet shop laminated back to back. They came out of rolled edge counters. Got them for free. Almost any countertop shop will give themn to you.

Before I glued then up I cut slots into them and mounted bolts to use to hold it to the saw table. Then mounted it between the rails of the Bies fence. Been using it for years, Still flat.

Re: Router table substrates

#10

Re: Router table substrates

Jim Dillon

Dale,

Two layers of 3/4 inch MDF certainly will do the job. I built my router table extension from a single layer of 3/4 inch MDF 15 years ago and it has held up very well. I built the entire TS extension table from one layer of 3/4 inch MDF on top of a frame of 1x4s (on edge) with multiple cross bracing of 1x4s. I surrounded the router opening with bracing as well.

For a finish, I applied multiple coats of natural Danish oil on the top and bottom and allowed each coat to dry well. I then waxed the top.

Woodcraft sell a phenolic coated 3/4 inch birch plywood material that I have used for a bandsaw table. It is nice stuff, but very expensive, and seems to scratch easily.

Jim