Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

How To STRENGTHEN Miter Joint

Posts

How To STRENGTHEN Miter Joint

#1

How To STRENGTHEN Miter Joint

Bob S

My Coffee table is coming along nicely. I have White Oak 2" square, cut on 45 deg. Miters. I will glue the four pieces together, and want to strengthen the joint. I realize that the glued surfaces are mostly end grain, and will need reinforcing. Can anyone provide any easy (boating season IS approaching!) solution. I am even considering angle brackets (hidden underneath), as i think cutting a floating m/t is way too difficult, onto that slippery 45% surface. What about a biscuit? My biscuit jointer goes onto 45, maybe that is an option.

Re: How To STRENGTHEN Miter Joint

#2

Re: How To STRENGTHEN Miter Joint

Jesse Cloud

If the table isn't going to get a lot of stress, biscuits should work and will get you in that boat in a hurry. More biscuits are better. I would use 3 or four on each miter. The bigger the biscuits the better.

Another option is to use a spline. Simply cut a groove in each miter face with your tablesaw, maybe 3/4 of an inch deep. Just be careful to cut it in the same place on each miter. Plane a board to the exact thickness of your groove and cut to length and width. The grain needs to run parallel to the floor, across the joint.

Glue and clamp and start getting that boat ready!

Re: How To STRENGTHEN Miter Joint

#3

I second the spline

Bruce, a MN Galoot

Re: How To STRENGTHEN Miter Joint

#4

Re: How To STRENGTHEN Miter Joint

paul in AZ

I wouldn't trust a biscuit.

A spline seems like the best way to go. If you don't want to see a spline you could cut one into the inner surfaces and not all the way through to the face but will lose considerable strength.

I kind of like to see splines. A contrasting wood would make it a design feature.

Re: How To STRENGTHEN Miter Joint

#5

Re: How To STRENGTHEN Miter Joint

Bob S

So, i will try a Splined Mitre joint, this table is gonna last!! And an open corner is not acceptable. More Info/Questions:

1. I should cut the slot into the face of the miter. I interpret that as 'along the 45 degree line'. So the slot, will be parallel to to miter joint, some depth into each of the joining pieces.

2. Grain direction of the wood? Does the grain need to run 'along' the miter joint, or 'across' the miter joint. JC suggested, 'grain runs parallel to the floor, across the mitre'. I am confused by this.

I understand the 'parallel to floor'. But will i rip, or crosscut a piece of oak for the 'spline'.

I will practice this joint today, please advise.

See attached image. This image looks contrary to my belief in that the spline is misplaced. Clarification, is definitely needed.

3. I really appreciate this help!

Bob


Re: How To STRENGTHEN Miter Joint

#6

Re: How To STRENGTHEN Miter Joint

Barry Irby

Bob, If I were doing that type of joint, I would move the spline as close to the inside corner as I could. Maybe a 1/8" in. This allows the spline to go as deep as practical, but leaves some "heal' as a fulcrum. If the spline is too deep the slot severs the "toe" and the little triangle pieces are weak and prone to crack, weakening the joint. I would make the spline with the grain aligned with the rails. Lets say the slot is 1/8" thick and half inch deep in each piece. The spline would be 1/8" thick. the width of the rails and close to 1" long. Do not make the spline too long, it will hold the joint open. Lets say its an off cut from the end of a board the width of the rails and 1/8" thick. Not a section of a board and inch wide and 1/8" thick. This avoids a cross grain situation. (A picture really is worth a thousand words, or at least a couple of hundred.) This is a blind or hidden spline.

An alternative would be to glue up the frame with the miters as butt joints and then cut the splines in across the corners. You would make a cradle for your table saw that allows you to hold the frame vertically so that the corner rides on the table with each side at 45 to the table, like a Vee. Cut through each corner with a blade that makes a flat bottom groove. (rip blade?) Fit triangular splines in the grooves and glue them in. You could have three of four at each corner.

They look vaguely like dovetails or a box joint. Generally you might consider contrasting wood and "celebrate" the joint or you could use the same wood and be more subtle. These are fast and fairly easy once you have the cradle. If you still don't understand after all my babbling, I could post a picture of my cradle.

You can also do this with a handsaw (Go directly to the quiet side) and veneer slices for the splines. You just have to match the veneer's thickness to the kerf of the saw.

Re: How To STRENGTHEN Miter Joint

#7

Re: How To STRENGTHEN Miter Joint

John McGaw

The easiest way I've found is to add feathers to the joint. They can be played down by using wood identical to to the frame or accented by using contrasting wood. Putting them into a joint is literally the work of a few minutes. Well, a few minutes after you take a half-hour to make the tablesaw sled to support the workpiece.

Re: How To STRENGTHEN Miter Joint

#8

Dale Lenz

Re: How To STRENGTHEN Miter Joint

Dale Lenz

Still confused to the final outcome of your coffee table, will the splines show?

Re: How To STRENGTHEN Miter Joint

#9

Re: How To STRENGTHEN Miter Joint

Bob S

Dale, The splines will show thru the ends of the joint. See a later post. It looks like "B" is the way to go. I have practiced the joint and it is not beyond my abilility i don't think.

Re: How To STRENGTHEN Miter Joint

#10

Re: How To STRENGTHEN Miter Joint

ash

I just made a jig for the drill press and double doweled the 2x2 mitered corners with 3/8" x 2" spiral dowels. Then glued and clamped. Very strong.