Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Vacuum pressing photos

Posts

Vacuum pressing photos

#1

Vacuum pressing photos

Grant in Iowa

A while back we were discussing the benefits and problems with vacuum pressing. I thought I'd share some photos of a part that just came out of the vacuum press this morning. I am making laminate bent water skis with Formica for the outside layers. There are 4 layers of Ash, and two layers of Formica on this part.

The first photo below is of the part fresh out of the press. I use Dap Weldwood acrylic resin and let it set up in the press overnight at 75 degrees and 26" of mercury on the press. The waxed paper I use to protect the bag and form from glue squeezeout is still on the part in this photo. When I am preparing the part to be placed in the bag, I use blue painters tape to hold the freshly glued layers of the sandwich in alignment and in the right place on the form.


Here's a shot of the blank with the waxed paper removed. This is #1, and I began to worry about starved joints when I saw the lack of glue squeezeout. I used a foam roller to apply the glue between the layers. I am not seeing any evidence of starved joints yet, but I will apply more glue to the next parts to be sure.


The process of shaping the part from this point goes like this. I make and perfect a template of 1/4" masonite of the outline of the ski. I lay and clamp this template over the newly formed blank and trace its outline on the concave side of the ski. I remove the template and cut the shape close to the line at the bandsaw. I reinstall the template with clamps and, using a bearing guided bit in a router, follow the template to create a part that perfectly matches the template. With a roundover bit, I slightly round the edges. Here's what it looks like after that process. All it needs is the edge lightly sanded and finished, and the hardware applied:


The real point of my post is to share the quality of the glueup using the vacuum press. Nice, fine gluelines, nearing the quality of baltic birch ply. Dap wants a glue thickness of .003" to .006" for best results. I started with a total material thickness of .730", and finished with a thickness of .750"... or about .004" per glueline. Right in the butter zone. I built a prototype ski last summer and it has held up well so far with similar glueline thickness.

Here's a couple shots of the edge and rear or the ski so you can see the gluelines (as well as my camera and photography skills allow, that is):



In the "If I had it to do over" category, (and I do, I have to make several more), I'd add a layer of hardboard between the part and the form in order to protect the form a bit.

Hope this provides some insight into the value of vacuum pressing when doing laminate bends, I know there was significant interest in the subject last time it came up.

Regards,

Grant in Iowa

Re: Vacuum pressing photos

#2

Re: Vacuum pressing photos

Doug Ring

Grant,

In a previous life, I ran a medium-volume skateboard shop (up to 100 boards/day), where we build the molds in-house, made mechanical presses in-house, and used epoxy exclusively. For a few years, approximately 20% of the business was building snowboards - your ski brings back a lot of good memories! If I had to do it over again, I'd definitely look at setting up some type of vacuum system.

A couple of questions:

* How did you source your ash veneer? Did you source from a veneer company, or cut and finish as needed?

* What type of finish are you using? This was always the concern with the snowboards - we needed a urethane that was durable enough to withstand incidental impact and had excellent water resistance.

* Why Formica top and bottom surfaces? The Formica that my dealer sells seems like it would be rather thick (and heavy) for this application.

Thanks,

Doug (in San Diego)

Re: Vacuum pressing photos

#3

Re: Vacuum pressing photos

Barry Irby

Can you tell us about your vacuum system? Is it a venturi system? If so, how big is your compressor?

I am pretty sure I am getting sucked into the vortex.....

Re: Vacuum pressing photos

#4

Re: Vacuum pressing photos *LINK*

Grant in Iowa

Hi Doug,

let me start by saying that the skis I am making will be used by a show ski team. They are on the water 4-5 nights a week during the summer either practicing or putting on a show. Durability is key on these skis.

Now, to your questions:

How did you source your ash veneer? Did you source from a veneer company, or cut and finish as needed? I am lucky to have a plentiful supply of low cost ash here in Iowa. With the Emerald Ash borer hard at work in Wisconsin, the price of ash is low here. I buy from a small local supplier and resaw the veneers myself to keep costs low. I resaw them at the bandsaw and then run them through my small performax drum sander with 80 grit to provide good tooth for the glue.

* What type of finish are you using? I have toyed with a few finish choices, but for now I am just using Helmsman spar varnish. It is one of the harder exterior grade varnishes I have found. I tried Sikkens Cetol, but found it too soft. We keep close eye on the finish and keep it recoated as needed...at least yearly.

* Why Formica top and bottom surfaces? I am using the thicker formica .050" thick for durability. As I stated above, durability is key on these skis. The skiiers come in and land on shore after each act, which would eat any bare finish alive. We get about ten years or more from a formica covered ski. Yes, it makes the ski a bit heavy, but these aren't jump skis, so the added weight isn't much of a problem.

The skis I am making now are for the "Around the Boat" team. In this act, up to 8 skiiers on staggered tow lines coordinate their cuts with the boat driver and make a circle all the way around the boat. To make it all the way around and keep going, they must ski at around 40 miles per hour. When things go bad, the skis can take abuse from the triple outboard motors or just other skiiers. A bare wooden ski wouldn't last very long. These skis aren't readily available from sports stores, and are costly to purchase for our nonprofit team. So I volunteered to make them to both benefit the team and my skills. I have thought of trying fiberglas or carbon fiber, but in the end Formica fits the bill and is cost effective.

Regards,

Grant in Iowa<---just put ski number two "in the bag"


Link to "around the boat" explained

Re: Vacuum pressing photos

#5

Re: Vacuum pressing photos *LINK*

Grant in Iowa

Barry,

My vacuum pump is a venturi system. I got it from www.Joewoodworker.com. I am not affilliated, but the owner of the site is a great guy and very helpful.

I bought the "V2" venturi kit, and put it together myself without much trouble. Basic wiring and plumbing skills (or an ability to follow instructions) are all that are needed to put it together.

I run it with a contractor style air compressor that delivers something like 7-9 cubic feet per minute at 90 PSI..don't recall exactly. Anyway it is a 1.5HP contractor grade unit with a twin cylinder pump and can run on a 15A circuit. Your basic compressor. The tank is about 10 gallons. I intentionally sized the vacuum reservoir on the venturi pump so the pump satisfies before the compressor cycles on. This gives the compressor a chance to cycle between cycles of the venturi pump.

I am pushing the limit with a 4x8' bag, but wanted to buy one bag and be done with it. I needed a larger bag for the length of the water skis. the large volume of the bag hasn't been an issue for the venturi pump. It actually isn't much of a liability to use a large bag on a smaller project, since you can roll up the unused bag and just use the area near the opening of the bag.

I should note that I minimize the work the venturi needs to do by drawing most of the air out of the bag with a shop vac before switching to the venturi pump to finish drawing down the bag. This isn't necessary, but speeds up the time required. The venturi pump would have to cycle two or three times in order to draw down a bag of this size. Once drawn down, the pump cycles about once every 20-30 minutes while the glue sets up. You can adjust the maximum vacuum pressure the system creates to control the clamping pressure via a small set screw on the pressure switch.

Regards,

Grant in Iowa


V2 at Joewoodworker

Re: Vacuum pressing photos

#6

Carbon fiber.....

Barry Irby

As with much of my information this is some half remembered bits and pieces. (So apply salt as needed) They use carbon fiber strip to repair basement walls that have cracked and are bulging. They glue them vertically across the cracks with epoxy. The straps appear to be hard, flexible and slick. Might be something you can use.

I have been reading the Joe Woodworker stuff.

I find the venturi systems to be astounding. The idea that you can generate a near perfect vacuum by blowing air through a port is just something I am having trouble wrapping my head around.

I have a 1HP compressor, so I am not sure about it. I also have a 1.1 cfm Gast vacuum pump. It appears both of them are sort of on the smallish side but may work. Going to have to give this a try.