Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Scroll Sawing Can Be Dreadful

Posts

Scroll Sawing Can Be Dreadful

#1

Scroll Sawing Can Be Dreadful

George Colonel's Workshop-Havertown PA

Good Evening Friends,

I've owned a scroll saw but never seriously used it. Now I have to make sets of chess men, 32 men per board, six boards. The chess pieces vary from 2 1/4" to 3 1/2". I am using poplar blanks, 1 1/2 inches square, and applying the templates to adjacent sides with spray adhesive. I am drilling holes in the bottoms of each piece for lead shot as weights. I am also drilling relief holes at transition points, about 20 per blank. I have the first 32 pieces fabricated. I bet I broke 20 blades so far. The blades are 18.5 tpi/pin type. I find the speed of approx 1400~1500 opm to be fast enough for smooth cutting, despite some mental lulling. Then a blade breaks with a loud bang and wakes me up. I bought the blades at Orange Borg ( Ryobi) and some at a local hardware store ( Olsen). I wonder if that degree blade breakage is a "cost of doing business", or a cost of learning to like a scroll saw. I feel like blowing it up when the projects are over.

I need some advice on blade sources, pin and pinless blades themselves, tension, feed rate, and a good place to recycle the broken items. At the rate I am breaking them, I'll have a hundred pounds of broken blades before I'm done. I'll be glad to see this phase of the project over.

George

Re: Scroll Sawing Can Be Dreadful

#2

Joe Bradshaw

Re: Scroll Sawing Can Be Dreadful

Joe Bradshaw

Colonel, I have found that putting a strip of clear package tape on the top and bottom of scroll sawn pieces helps a lot in limiting blade breakage. The tape seems to lubricate the blade. Also, slow down your feed rate and let the blade do the cutting. You can also play with the tension on the blade. Good luck.

Re: Scroll Sawing Can Be Dreadful

#3

Re: Scroll Sawing Can Be Dreadful

Phil Joines

Have you adjusted the saw so the blade moves vertically? Like most tools scroll saws aren't adjusted correctly at the factory.

Re: Scroll Sawing Can Be Dreadful

#4

Re: Scroll Sawing Can Be Dreadful *LINK*

Janice Manuel

Compound sawing is tough on blades under the best of conditions. And, you won't find good blades at any of the big box stores. Some Olsen blades are good, but you won't find them at HD.

The packing tape trick helps a lot.

What saw are you using? Will it take pinless blades?


http://truecutblades.com

Re: Scroll Sawing Can Be Dreadful

#5

Re: Scroll Sawing Can Be Dreadful

Joseph Mulherin, Sr.

Hi, Colonel, in my scroll sawing projects I have found out that the blades are not used the entire length of the blade in sawing....so after a while I reverse the blade top for bottom and continue until that section also gets dull and does not cut as smoothly as new cuts. And I let the blades do the cutting....not forcing the material into the blade but just gentle pressure letting the blade do the work....and the plastic tape mentioned is also a good item to consider for the lubrication during the cutting.

My saw uses the pin blades which I purchase at my local Lowes store.

Re: Scroll Sawing Can Be Dreadful

#6

Re: Scroll Sawing Can Be Dreadful

Terry Quiram

Good Morning George

My scrolling experience is over 20 years. I think 2 issues are responsible for your blade breakage. The first issue is that your blade is probably over tightened. You may be stuck with this one as I don't remember pin end blade machines being able to adjust tension. The second issue is the blade speed and feed rate. Any wood thicker that 3/4 requires a slower cutting rate and slower feed rate. As suggested slow down and let the saw do the work. The tape suggestion is a very good tip. Have an extra beer when finished.

Re: Scroll Sawing Can Be Dreadful

#7

Re: Scroll Sawing Can Be Dreadful

del schisler

here is the blades you need to get I have a hegner scroll saw and The blades get dull before they brake Which is almost never unless you push to hard Which i belive mean's that the blade isn't cutting good here is the link You can call Mike and talk to him These are the best blade's you can buy http://www.mikesworkshop.com/blades.htm I didn't read the other post yet so maybe some one already posted Mike's site

Re: Scroll Sawing Can Be Dreadful

#8

Jason Roehl in Lafayette, IN

Re: Scroll Sawing Can Be Dreadful

Jason Roehl in Lafayette, IN

Terry, I remember your scroll work. I think I may even still have a piece. I actually had the breakage problem at the other end of the spectrum when I (rarely) used my scroll saw. I wasn't getting the blades tensioned enough, and they were breaking as a result. So, the last time I used it, I took some time to re-educate myself on how to tension the blades on my saw, and it suddenly cut much better, both in terms of speed and smoothness. Still a cheap saw, though!

Jason

Re: Scroll Sawing Can Be Dreadful

#9

Re: Scroll Sawing Can Be Dreadful

BrianA

Here is a great place for scroll saw info. Good forum and friendly people. Many people at the site recommend Mikes for blades. It will make a big difference.

Check out this site.

http://www.scrollsawer.com/forum/

Brian

Re: Scroll Sawing Can Be Dreadful

#10

Re: Scroll Sawing Can Be Dreadful

FredD

Janice used to demo Dewalt's scroll saw, she is just to bashful to say so.;-))

For myself I like Precision Ground Blades that cut on the up and down stroke, also I never seen a blade with the number of teeth you mentioned, might try 5 or 6 to the inch.

FredD

Re: Scroll Sawing Can Be Dreadful

#11

Saw Types and Blades--Mini Gloat

George Colonel's Workshop-Havertown PA

Good Afternoon Janice,

As it happens, I am now using two scroll saws. Each is 16" capacity. I have owned a two speed AMT for years. I visited my hardware store to got a re-supply of blades while I considered the forum's on-line sources, and got into a conversation with the store manager about blades and scroll saws. He had recently bought out the previous owner and was liquidating inventory. He had a new ACE variable speed marked down from $109.99 which he "gave"me for $35.00 with two packs of Olsen Blades. I haven't used the new saw for more than a couple chess pieces, so can't testify to its fine points yet. It does break blades as well as the AMT, though. Still, the price was right, and I can always give one of them to one of my kids.

Each saw can run pinless blades. I have been using pin type blades in them, as they seem easier to load--and I am getting pretty good at that!

George

Re: Scroll Sawing Can Be Dreadful

#12

Re: Scroll Sawing Can Be Dreadful

McKay

I have used the flying dutchman at the school for years. I have three hawks that I think have broken maybe one blade every week or so. They usually get dull and they are tossed. I buy them by the gross and have been very satisfied. Personally I have the 30" general. I have only had it a short while and it will be a very long time before I am ever able to use it to its maximum usage. I used a cheap Delta before that and was able to do a few nice things with it. The General excalibur is very quiet and a joy to use. :D

Re: Scroll Sawing Can Be Dreadful

#13

Re: Scroll Sawing Can Be Dreadful *LINK*

Frank Orfanello

George,

i second the two recommendations you got, one regarding tape, it works like magic, and the second regarding mike's saw blades. These are by far the best scroll saw blades I've ever used.


http://www.mikesworkshop.com/blades.htm

Re: Scroll Sawing Can Be Dreadful

#14

Re: Scroll Sawing Can Be Dreadful

Mac

It seems that everyone has told you about blades and tension but failed to mention the problem. You say you go into some mental lulling and then a blade breaks and wakes you up. The problem is obvious, you need hearing protection so you don't get so rudely awakened. :)