Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

OT - Odd plumbing fixture question

Posts

OT - Odd plumbing fixture question

#1

OT - Odd plumbing fixture question

Nat Robison

I'm helping some friends renovate a small bathroom and the new vanity will be in the way of the toilet supply so I'm trying to come up with a different shut off valve for the toilet supply (the new vanity comes within a half-inch of the supply).

The one in question looks like about 4 inches of chrome coming out of the wall and it's soldered to copper right about where it meets the wall. The shut-off is on the end but there's no compression nut, it looks like maybe the whole valve screws onto the pipe but there's no evidence of any threads on the pipe (that I can see). Is it possible that the valve and chrome piece are one? It wouldn't really lend itself to changing if that's the case.

Basically, I need a valve with the "knob" perpendicular to the wall, instead of parallel. With the new vanity, I won't be able to open the valve (if it's parallel to the wall). I'm hesitant to wrench on this thing if I don't know how it's put together. Any thoughts? Anyone seen this before?

Re: OT - Odd plumbing fixture question

#2

Re: OT - Odd plumbing fixture question

steve mackay

I'm probably thinking wrong but . . . is the body of the valve "squared off" so that it might accept a wrench around it ? MIGHT indicate that its threaded. If still in doubt ask someone with mre experiance to take a look IN PERSON. Personaly, I DID try unscrewing a sweated fitting once. It DID come off. OH BOY, did it come off ! BIG hassel inside a wall.

Re: OT - Odd plumbing fixture question

#3

Re: OT - Odd plumbing fixture question

del schisler

Unless they ground the chrome away down to copper than it can be soldered any way if the pipe is 1/2" copper which is what is should be it can be cut off and get a 1/2" Compression to 3/4" valve for this That is what the bath room fitting is Any box store will have this Now if by some mean's it is 3/4" copper you can still get a valve to fit 3/4" to 3/4" Compression Just take a piece of pipe to the store for a fit good luck

Re: OT - Odd plumbing fixture question

#4

Re: OT - Odd plumbing fixture question

Barry Irby

Locally what is used is a piece of 1/2" threaded pipe the is plated with chrome. There is usually an eared ell in the wall. The pipe is screwed into the ell and the stop or valve is screwed onto the end of the pipe. I have never seen a chromed pipe that was soldered into the pipe/fitting in the wall. I have never seen one with the pipe and stop made together. OTOH I have not seen them all and I don't know every way they have ever been done. There is a plumbing forum on line I think. Maybe someone will throw out the name.

If the pipe and stop are two different pieces you may be able to unscrew the stop from the pipe and wrap the threads with new Teflon tape and screw it back on and turn the handle to the side. IF you try this you should wrap the pipe with cloth or tape to avoid scarring it, grip it with pliers and use a wrench on the stop.

It might be simpler to carefully open the wall and inspect the situation. You might be able to remove the fasteners holding the eared ell and move it far enough to solve your problem. I am never that lucky.

Re: OT - Odd plumbing fixture question

#5

Re: OT - Odd plumbing fixture question

FredD

Nat,

A common way of handling this would be for the toilet supply and the cold water supply line using a angle stop made for this purpose.

So your toilet supply enters the vanity though a neatly bored hole and is fitted to the cold water combination angle stop.

That being said , you need a Plumber for this.

FredD

Re: OT - Odd plumbing fixture question

#6

How about a picture

Gary Camp, Bend, Oregon

Before you do anything make sure you know where the main shutoff to the house is. If by knob you mean the valve handle you may be able to rep-lace the existing valve with a screwdriver angle stop no handle at all. a picture might help.

glc