Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Only three days left on the Laguna Sliding Table!

Posts

Only three days left on the Laguna Sliding Table!

#1

Only three days left on the Laguna Sliding Table!

Scott in Montana

There are only three days left to bid on the Laguna sliding table up for bid in the Benefit Auction for Wood Central.

So far the top bid is only $200 for this $1000+ sliding table.

Let's raise some more money this fine forum! Bid high and bid often! :O)

Thank you,

Scott in Montana

Re: Only three days left on the Laguna Sliding Table!

#2

This is a high quality saw

McKay

I have one of these saws in my school shop and it is very good quality. When the district mandated that we switch to saw stops, I would not let them switch out the slider because ST did not have any thing that would do the same job. It would be a real shame if this saw went for that little. I no not know if this comes with the scoring saw, but it can be added. Does beautiful cuts on melamine and hardwood plys.

Re: Only three days left on the Laguna Sliding Table!

#3

Re: This is a high quality saw PART

Mark Mandell - Gone Round In Jersey

He's auctioning just the sliding table, not the whole saw.

If I had room in my shop, I'd take it.

But Alas . . .

Re: Only three days left on the Laguna Sliding Table!

#4

sorry, my bad

McKay

Re: Only three days left on the Laguna Sliding Table!

#5

Nah, WC Loss

Mark Mandell - Gone Round In Jersey

Were it the whole saw, I'm sure it'd be gone by now, and the new server would be paid for in one swell foop. :D

Re: Only three days left on the Laguna Sliding Table!

#6

Questions????

Barry Irby

I am not familiar with a sliding table. Never seen one. What does it do for the wood worker? Is it a sophisticated miter sled?

Would it fit on a Delta contractor saw that is forty years old? That would be amazing. A $350 saw with a $400 Biesemeyer fence and a $1200 sliding table. Would the Bies fence be in the way?

Daydreaming here, my shop is too small.

Re: Only three days left on the Laguna Sliding Table!

#7

JL

Re: Questions????

JL

Would it fit on a Delta Contractor's saw?? Probably.

It usually just mounts to the side of the main table.

Would the Bies be in the way? Again, probably. The fence usually has to be moved over a bit to mount the sliding table on the saw. If your Bies mounts the traditional way, this means you would have to remount it so that the rail starts at the edge of where your wing would be.

It does take up a bit more space - it would probably jut out about 3-4' from the blade on the side and about 1-2 feet extra in the front and back.

Just think - picture perfect cross cuts. It would make handling sheet good easier.

;)

Re: Only three days left on the Laguna Sliding Table!

#8

Just a couple additional notes

Scott in Montana

I think Barry has done a good job of answering your questions. The one thing I'd like to clarify is that I bought this sliding table because is was much more compact than the other tables. This one only adds about 5" beyond the width of the stock wing to the left of the blade. That's with its miter fence removed. So it doesn't dominate your shop when you're not using it.

I should add, this sliding table can be used when your saw is on a mobile base since it only bolts to the saw and doesn't require permanent outrigger legs unlike other models such as the excalibur.

One more thing, I use the exacta TS-III fence on that saw so I just slid the rails 9" to the right.

I couldn't live without a sliding table anymore... I'm spoiled! :O)

Scott in Montana

Re: Only three days left on the Laguna Sliding Table!

#9

Two Days Left!

Scott in Montana

Re: Only three days left on the Laguna Sliding Table!

#10

Sorry, make that JL did a good job answering Barry

Scott in Montana