Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Question about cutting curves

Posts

Question about cutting curves

#1

Question about cutting curves

Mike Rubes, Apex, NC

Hi all,

First time I've asked a question on this side in years! I spend most of my time on the turning side, but find myself making a cabinet and have a procedural question.

I would like to cut a curved front of the cabinet (from plywood) and cover it with solid wood edgebanding. Imagine a demi-lune table made of plywood with a solid wood edge band and you get the idea of what I am after. Now, I could just make the joint between the plywood and the solid wood a straight line and put the curve on the edge of the solid wood, but what if I wanted the plywood to match the curve of the outside of the solid wood edge banding? I am planning on use contrasting plywood and solid wood for effect and think if the ply followed the outside curve of the finished piece, it would look good.

Just curious how people here would go about cutting that to get a nice, tight fit? I've got a couple of ideas, but would love to hear from those more experienced than me.

If that description is not clear, let me know and I will try to draft a picture and post that.

Thanks!

Mike

Using the lathe for a hat storage for the next few weeks in Apex, NC!

Re: Question about cutting curves

#2

Re: Question about cutting curves

Barry Irby

Are you saying you want to cut a curve or circle on the edge of a piece of plywood and then cut a matching Piece of hardwood to glue onto the edge? Sort of a male/female fit?

If that's it, I think Carol Reed is the Router Lady and she wrote a book that explains it. Its called cutting Sympathetic Curves. (I think). Actually sympathetic curves may typically be serpentine and not just a simple circle or oval, but the technique would work for a simple curve.

So, Carol posts on the round side. Go back to familiar territory and ask her directly.

Re: Question about cutting curves

#3

Re: Question about cutting curves

Carol Reed

I look at this side, too.

It is called complimentary template routing. Close, Barry. :D

I will not make an attempt to explain it here. There is a whole chapter in my book with lots of pictures. Router Joinery Workshop

Lots of libraries have a copy as it was recommended highly as a library buy. Of course, it would be better if you had your own copy! :) :) Still available on Amazon.

Re: Question about cutting curves

#4

Re: Question about cutting curves

Barry Irby

Sympathetic/Complimentary What's the big difference?

Sometimes I know what to do but not how. Sometimes I know How to do it, but not what. This time I did not even know what to call it, but at least I knew who to ask. Now I am so confused I have got to go back and look at your answer again.

Re: Question about cutting curves

#5

Re: Question about cutting curves

Mike Rubes, Apex, NC

Thanks, guys. My local library has Carol's book, so I will stop by tonight and take a look.

Thanks,

Making things round without the lathe in Apex, NC

Re: Question about cutting curves

#6

Ellis Walentine

Edgebanding?

Ellis Walentine

Mike, if all you're trying to do is edgeband a curved tabletop, just rip a strip of whatever thickness and bend it around the curve with a band clamp. If what you're talking about is solid edging, say a 2" band of solid wood, then the trick is to first glue up segments of solid wood to form a rough blank, and then rout the complementary curve in it to fit the curvature of the table top. The number of segments is somewhat arbitrary, although you want to err on the high side so you don't introduce more short grain at the ends than necessary.

If I'm reading you wrong or you have other questions, let me know.

Ellis

Re: Question about cutting curves

#7

Re: Edgebanding?

Mike Rubes, Apex, NC

Hi Ellis,

Thanks for your note. The second thing you describe is what I am after. A 1 inch or so edgebanding. My question really concerns getting the rounded egde of the outside of the table to match the inside curve of the solid wood banding. I definitely figured a router was the way to do it, but getting the circles to be the exact size to fit is my question.

I'll take a look at Carol's book at the library tonight and see what it says. My off the cuff idea involved mounting my router on a pivoting axis to swing the curve, but then I faced with that fact that my inside circle is smaller than my outside circle, so they wouldn't match just right.

I was thinking I might could do this with my inlay kit and a fixed curved template. There is not rush on this so I can take my time and play with it.

Thanks again for your note.

Mike

Exploring the curvature of wood-time continuum in Apex, NC

Re: Question about cutting curves

#8

Re: Edgebanding?

Bob Entwisle in NJ

Unless I misunderstand, can't you set the jig up for the radius of the inside curve, then to cut the outside, increase the radius by the width of the edge band plus the diameter of the router bit to cut the outside curve.

Bob in NJ

Re: Question about cutting curves

#9

Re: Edgebanding?

Jorge Casta�eda

Hi Mike,

You need to make a template on say, 1/4" plywood, fuss with it until it is what you want. then use a router with a pattern bit, it has a bearing on top, follow the pattern with the bearing, making sure you stay always touching the pattern.

Make a practice cut on ply or lesser wood, then cut your piece, then use the work piece to cut the matching border. Now you have two matching pieces,the glue line, now to cut the exterior, you may need to enlarge the design, so make another pattern until you like it. etc...

It is harder to explain than to do..

Have fun

Re: Question about cutting curves

#10

Ellis Walentine

Here's how I used to do it

Ellis Walentine

It was a lot easier when I had an industrial pin router in the shop, but you can do this trick with a router, a 1/4" straight or up-spiral bit, and 1/2" and 1" template bushings.

1. Rout the template. Use the 1/2" bushing. Rout through the template material. This creates an inside curve offset 3/8" from the table top.

2. Glue up your edge material. Cut mitered sections of over-width (and over-thickness) material and join them together with splines and glue.

3. Rout the complementary curve. Lay your template over the glued-up edge blank. Use the 1" bushing to create the complementary 3/8" offset.

Hope this helps. Pardon the quickie drawing.

Ellis


Re: Question about cutting curves

#11

MicroFence

charlie belden

Probably not cost effective for a One Shot, but the MicroFence can do matching curves - even long radius curves - very precisely - as in Dial In - literally - how much slop you do or don't want - in 0.001" increments. Michael Fortune did a big, long radius demilune type piece using a MicroFence. Comes in real handy if you're going inlay banding as well. Add on MicroFences precision plunge router base and you've got a 2 1/2D mill.

Re: Question about cutting curves

#12

Ellis Walentine

That works if....

Ellis Walentine

... the curves are actual circle segments, and any router trammel will do the trick, though the Micro-Fence makes it easy to make adjustments in tiny increments.

Ellis