Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Porter Cable 853 cordless drill driver

Posts

Porter Cable 853 cordless drill driver

#1

Porter Cable 853 cordless drill driver

Don Orr

I have 2 PC 853 type 1 cordless drill drivers and would like to remove the keyless chuck from one of them. I managed to get the screw out from inside the chuck but can't get it off. Any ideas ? Is there some special tool required maybe? I tried just wedging it off with a screwdriver but no luck. I also would like to get the chuck off of my PC 850 so I can replace it with the keyless chuck from the 853. Any help will be greatly appreciated.

Thanks, Don.

Re: Porter Cable 853 cordless drill driver

#2

Re: Porter Cable 853 cordless drill driver

Barry Irby

Don, I did this years ago on another brand of drill. The chuck was threaded on on mine. Put the short end of a large Allen wrench in the chuck and whack the longer end with a small hammer or even a hardwood stick. The question is which way to whack it. I believe mine was left hand threads and very snug. It might be opposite the threads of the screw you removed and it could be splined. If it is splined you might be able to turn the Allen wrench around and put the long end in the chuck and whack it in the "out" direction.

You can go on the PC site and look up the manual and parts list.

Re: Porter Cable 853 cordless drill driver

#3

I wonder....

Barry Irby

If you had an impact driver if you could put a bit in it and chuck that bit into the drill (so they were chuck to chuck) and use the impact driver to unscrew the drill chuck?

Re: Porter Cable 853 cordless drill driver

#4

Re: Porter Cable 853 cordless drill driver

Don Orr

Thanks for the input Barry. I looked into the chuck after taking the screw out and there is no hex socket to get an Allen wrench into. If it is threaded onto the motor shaft I don't know how I could get a good hold of it and not have the motor just spin. The switch is dead and a new one is $57-more than I want to sink into it at this point. I was hoping to be able to salvage the keyless chuck though.

I did find a parts diagram but it was not very helpful.

Re: Porter Cable 853 cordless drill driver

#5

Re: Porter Cable 853 cordless drill driver

Barry Irby

Don, I was not clear. Tighten the chuck onto the short end of the Allen wrench, a sturdy one. Put the short end into the chuck so that it looks like a propeller with only one blade. Then sharply tap the end of the Allen wrench in such a way that you cause the chuck to suddenly spin. You could simply use it as a wrench and turn it with your hand, but you have no way to lock the shaft. What I am suggesting is that you use it as a home made impact wrench. You provide the impact by hitting it in the rotary direction with a sharp blow from a hammer or a stick. If it is threaded and you can figure out the right direction, once you crack it loose it should just unscrew. I'm thinking left hand threads, but I have left right orientation issues, so think it through for yourself. Heck, whale it both ways, you are trashing the drill anyway.

Re: Porter Cable 853 cordless drill driver

#6

PS, I looked up the diagram too....

Barry Irby

in two or three places and got nothin. No detail at all.

Re: Porter Cable 853 cordless drill driver

#7

the main threads on chucks are right hand thread

Bill Houghton, Sebastopol, CA

going back to the days when drills ran in one direction.

The screw down in the center of the "hole" in the chuck is left hand thread. The two threads work in opposition to keep the chuck on the drill when you're operating in reverse.

Once you tighten the allen wrench in the chuck, bash the other end in the direction that it would be turning if you were drilling.

I want to emphasize Barry's part about it being your very own impact driver - you want a sharp, firm hit to shock the chuck loose. Once it starts turning at all, you can probably unscrew it from there.

Re: Porter Cable 853 cordless drill driver

#8

Thanks Guys!

Don Orr

Barry-your DIY impact driver did the trick !

Bill-you are absolutely correct about the thread directions.

I now have a PC 850-which did not come with a keyless chuck-with a keyless chuck. Unfortunately it only has a single speed range-the 853 has Hi/Low. But I'm back in business and it didn't cost me a thing. Gotta love salvaging parts from dead tools. Especially when it ends up as an improvement to the one you're fixing.

Thanks for the help !

Re: Porter Cable 853 cordless drill driver

#9

Great, glad to help.....

Barry Irby

I could have done it much faster than the time it took me to explain it. I have a terrible time with which way things turn. My mind spins faster than the drill while I try to visualize it and explain it, but I could have done it instinctively and with out much thought. Glad it worked for you.

And I am like you, I hate it when old tools give up the ghost and try to salvage parts when I can.