Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Japanese Ofuro

Posts

Japanese Ofuro

#1

Japanese Ofuro

Richard

Anyone ever built a traditional Japanese Ofuro???

I can import one from Japan, made of native Hinoki for about $6,000 but before doing that I am considering a DIY project.

I have a lift of Clear All Heart KD oldgrowth Redwood that I have had for about 30 years and have never been able to decide what was special enough to use it for, maybe an Ofuro is the right project.

A couple of important issues; How do I build a watertight box approximately 4'x2'x2' and second, Redwood has a lot of soluable (?) tannins and oils that most likely freely leach out during use and I don't want to come out of the tub impersonating a Native American. I presume that multiple filling, heating and draining cycles (maybe with a little bleach) will solve the red stain issue hopefully, someone might have some experience with this.

Any input or thoughts on either issue would be much appreciated.

Thank you, Richard

Re: Japanese Ofuro

#2

Re: Japanese Ofuro

Glenn Madsen near San Francisco

Wow. I hadn't seen something like this for a lot of years. Brings back neat memories.

Thirty seven years ago, right after we got married, LOML and I house sat for a family in the hills above Berkeley, CA in the eucalyptus woods. The house had an authentic ofuru, and I came to really enjoy it. We were there maybe 6 or 8 weeks, andit was neat to soak away the aches of the construction work I was doing, helping build various stuff in town. Japanese stuff, really. Although what I was doing was shovel work, mostly.

Fast forward maybe 6 or 8 years, and my parents built a house, and had the builder put in a similar tub, in fiberglass. That was also a good deal, and worked well. Only minor leaks, and that from the pump system, common in hot tub type baths.

Forward to the mid-1980's, and we bought a house with an 8' redwood tub in the back yard. Hooked up to a pool-sized gas heater and pump, it could go from outside air temperature to lobster-cooking in about 20 minutes. It was one of the better things about the house. The tub heater worked better than the one for the house to which it was attached. And the tub was popular, and well-used.

Ahead to the late 1990's, and another house. The Jacuzzi we bought sucked, and got given away after years of neglect. If I had a lift of redwood, in good shape, I'd build another redwood tub in the back yard, and raise the fence so that we had more privacy. That's the trade off. These tubs, at least in California, need to be outside, because they leak or splash, and the weather is nice enough to enjoy 360 days a year where I live. Inside, I can't as easily deal with the moisture.

But redwood is a cool material to work with. Gets used for wine vats a lot here in NorCal...

Re: Japanese Ofuro

#3

Re: Japanese Ofuro

Thomas S Stockton

no idea what an ofuro is but I assume it is a soaking tub. Redwood will work fine no leaching of color or anything. Redwood got used for a lot of hot tubs and was also used for large water tanks. My house started it's life as a very large water tank in the east bay hills of the bay area. My current spring box for our ranches water supply is made of redwood with no bad effects.

Re: Japanese Ofuro

#4

Re: Japanese Ofuro

Richard

Hi Thomas,

Wow, wonderful house, love it, thanks for the input

Richard

Re: Japanese Ofuro

#5

Re: Japanese Ofuro

Richard

Hi Glenn,

The Berkeley Hills before the fire were wonderful, don't know what they are like now. I don't have your weather, I'm in SW Wash St. My plan is to have the ofuro semi-outside, I will enclose part of my deck with a sunroom that will open a lot, I need a place for my plants to winter, also for me to winter :)

Now I need to figure out how to make this box hold water and stay together

Thanks for the thoughts, at least I shouldn't have to worry about the color problem.

Richard

Re: Japanese Ofuro

#6

Re: Japanese Ofuro

Gary Camp, Bend, Oregon

I might try going to a Sushi place and getting one of the wooden Saki boxes (I don't have a clue as to what they are called) See how it is put together, they seem to be liquid tight.

glc

Re: Japanese Ofuro

#7

This will be interesting.

Barry Irby

I know how they do it on a small scale, like a box for water stones, but I wonder how they don it on a larger scale?

Wine barrels are done with staves that are assembled around the ends. The hoops pull the ends down to the size of the bottom and top and they fit into rabbets.

On a large square tub you would have to allow for the expansion of the bottom. Or would you? The bottom and the ends may expand at the same rate. In that case how do you account for the fact that sides would expand and the bottom would not along the length of the bottom boards?

Perhaps they are built with the boards in the sides horizontal and thus with the same grain orientation as the bottom boards and the end boards are vertical. They you would only have to deal with differential expansion in the vertical corners.

How about using one of blue swimming pool liners with the little dolphins? Think of the tranquility. NOT.

Take anything I say with a grain of salt. I am on the East Coast and have never seen a real one. What I have seen is lots of wooden hot tubs that rotted and fell apart. After a while even redwood succumbs to hot water. Seriously, Use truly excellent fasteners. Everyone I saw had fasteners that rusted and fell apart. Either they were crap or again everything succumbs to hot water.

Have you Googled this?

Re: Japanese Ofuro

#8

Re: This will be interesting.

Richard

Hi Barry,

Thanks for all your thoughts. Here's my current thinking, everything subject to change, I don't know how this handles the expansion issue, maybe you will comment on that.

The sides and end grains will all run horizontal.

The length of the sides will be a bit longer than the centerline length of the tub, ie, the ends will be set in from the ends of the sides, hope that makes sense

The bottom will be the same length as the sides

The bottom will be dadoed into the sides, the ends will be dadoed into the sides and into the bottom

The long joints of the stacked boards will have a blind splined canoe joint

No glue will be used

I'm not going to trust a doweled dado between the sides and ends to hold everything together so I will come up with some kind of a fancy external side to side tensioner mounted behind the ends. Much like a couple of pieces of all-thread with washers on the face of the sides, but much nicer.

The splined canoe joint is similar to a joint that log house builders use but they have the advantage of the weight of everything above keeping their joints tight. In this tub, since there is no weight above to use, the spline will have to be both a water barrier and a tension unit to keep everything together and the only way that will work is if everything swells tight when filled with water.

Any and all thoughts and comments will be appreciated

Richard

PS, After having written this it seems that maybe I ought to consider using some glue on the splines but being constantly wet might create more problems

R.

Re: Japanese Ofuro

#9

Re: This will be interesting.

Barry Irby

Richard, I spent a while on the Internet looking up these tubs. Did not do much toward answering my questions. I found web sites that discussed building them, but only in the sense that people said they wanted to, but not how to actually do it. No plans or construction details. The pictures all took me to sites about how to buy one.

It appears they usually run the sides and ends horizontal. No explanation of how to make this work with regard to expansion.

If your plan is to make a box 4' long, 2' wide and 2' deep and the grain in the sides and bottom are parallel to each other and the ends are vertical as if the bottom had been "folded" up I think you have the est shot. This is an intuitive assumption based on nothing but intuition.

I was thinking of a glue joint type joint. Several small tongue and grooves. I think this would get tighter as the wood swells. (not sure, but it seems it would be tighter than a butt joint. I hand not thought of a spline and I am not sure how it would affect the water tightness of the joints. Would the spline and joint swell at the same rate and would than leave the joint just as "loose" after it was wet?

3M makes a glue called 5200 (I think) that looks more like caulking than glue but is water proof. I built several small bridges by laminating arches out of treated 2x4's and they are fine after over ten years. The glue takes a week to cure.

I agree that you would need some sort of restraint across the ends to hold the whole thing together. I suppose you could look up the expansion of the end and allow for it, but that would be tricky. It might be better to use some really strong springs that would apply pressure but still allow the box to expand. Picking those springs would be equally tricky. Perhaps you could use the Shrinkulator to figure out the expansion.

Re: Japanese Ofuro

#10

Frank Klausz "Gasket" Trick

charlie belden

Frank Klausz uses a neat feature of wood to make a wood "gaskets" for water tight dovetailed boxes he makes for japanese waterstones. The idea might work for your soaking tub project. Here's how it works.

Join the edges of all parts.

On one edge face of each abutting part, place a small steel rod on the center of the edge face.

Pound all the way down the rod to create a long dent in the wood to compress a line down the center.

Join the dented edges again - using a VERY LIGHT cut.

Band the resulting edges together and fill the tub with water. The compressed wood will swell, creating a water tight gasket seal.

Only works on side and face grain, not on end grain, so sealing the bottom is your next "challenge"