Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Alkyd paint question

Posts

Alkyd paint question

#1

Alkyd paint question

Nathan

For a project I'm working on I decided to use alkyd paint. I'm rolling it on with a roller. First I put a coat of primer on and, being distracted by other stuff, let it dry for a long time. It sanded quite well. I hand sanded to 240-grit and the surface felt very smooth.

Now, 24 hours ago I put the first finish coat on, again using the roller. I was pleased with how it turned out but it needs more (wood grain is visible) probably two coats more. The surface looks nice (like an egg-shell, as advertised) but is a bit rough to the touch and I don't want the roughness to get any worse as I apply more coats.

I tried sanding with 240-grit but it quickly gummed up the sandpaper and I did not get the really smooth surface like before on the primer.

I'm assuming this is because it's only been curing for 24 hours and the temperature in the shop is fairly cool, arout 55 degrees, so the paint is not yet completely cured. Is this assumption correct, do you think? Also, is sanding between the finish coats the right thing to do, and what grit or grits would you use?

Thanks as always for any advice you can provide. Even if it's not about alkyd paint in particular, any general advice would be appreciated as I am a beginner.

Re: Alkyd paint question

#2

JL

Re: Alkyd paint question

JL

In my experience with eggshell paint, it takes quite a bit of time to "cure out". The solvents evaporate from the surface first. As the surface "skins over", it takes more time for the solvents to evaporate.

So - figure on at least a week - especially at lower temperatures. I wouldn't be surprised for it to take a bit longer. My own personal quick and easy "test strip" is to paint a coat on a piece of polyethylene plastic. When it can peel or crack off of the plastic, it is dry.

Some paints remain somewhat flexible and will always gum up your sandpaper to some extent.

Re: Alkyd paint question

#3

Re: Alkyd paint question

gary peterson

Sanding to 240 is probably overkill as there isn't any bite for the next coat. AS far as the grain showing, could have used a grain filler prior with a sealcoat shellac barrier. now, Each coat will dry the same thickness, thus your grain will never fill, and if it does I would presume the finish thickness will be, well, thick.

The temp will have an effect on your drying time, and if this is an alkyd(I am thinking benjamin moore Impervo type stuff) your "drying" time has to be extended, that doesn't include the "cure" time which can take several days in higher temps.

Re: Alkyd paint question

#4

Live and learn

Nathan

Thanks, JL and Gary. Yes, it's a tixotropic alkyd paint. The primer, I believe, filled the grain, but I probably should have used two coats of primer instead of just one. "Live and learn"

One more question on sanding. When one is putting on, say, three finish coats, is it standard practice to sand after finish coats no. 1 and no. 2?

I believe that in this case the primer serves as a grain filler. Don't know about the shellac barrier, though - here in Europe it seems shellac has fallen into disuse.

After sanding, the primer coat was very smooth. No tactile sign of any grain whatsoever. But you could _see_ the grain still, through the paint. Now, after the first finish coat, you can still see it, but substantially less. You cannot feel the grain, however. That's why I'm hoping that another two coats will fix the problem.

What JL said about the drying/curing process is exactly what I'm seeing. The outside of the paint dried very quickly, but just underneath it is still a bit gummy.When I tried sanding it, what happened was I compromised the outer shell, exposing the still-somewhat-gummy interior.

Re: Alkyd paint question

#5

JL

Re: Live and learn

JL

I don't usually sand - I scuff. I usually use a white abrasive pad. It knocks down everything without scratching the heck out of the paint. I usually scuff between coats.

If I am painting several layers in quick succession, I won't use an abrasive pad at all. I'll simply paint.

A lot of what you want to do is determined by the final look that you want to achieve. I often try for a "worn" "layered" look. I'll paint, rub, paint again (with a different color). After a bit of drying I'll try to scuff through in spots. I then cover with another finish such as BLO/Poly/Mineral spirits.

Re: Alkyd paint question

#6

Re: Alkyd paint question

Howard Acheson

Oil based alkyd paints are sensitive to temperature. Most paints are designed for application at 70 degrees and 50% relative humidity. At 60 degrees the drying/curing will be about doubled. Below 55 degrees, it may not cure at all. The air, paint and item being coated should all be at the same temperature.

Re: Alkyd paint question

#7

Re: Live and learn

FredD

"Live and learn"

Speaking of which, how did the DVD on sharpening work for you ??

FredD

Re: Alkyd paint question

#8

Live and learn to store clamps

Nathan

Hi Fred: I sent you an email about that awhile back, using the address from your profile here, but apparently you didn't receive it.

The short answer is: I ordered the DVD from L-N, it arrived, but I haven't watched it yet :|

Sharpening is going well. I got my oilstone flattened, acquired some nice locally made ceramic stones, and learned how to sharpen knives (by hand). I'm getting better at sharpening, but I need to work on my hollow-grinding technique. I also need to install the Wolverine Grinding Jig on my bench grinder.

Since I last wrote, I finished my first piece of furniture - a kitchen stool in spruce, with 8 haunched M&T joints and 8 regular M&T joints all cut by hand. Earlier on I had prepped stock for the legs by hand, but someone threw them away, so Master jointed and planed new stock for the legs, and for the top as well. The glue-up went well, but I haven't got to finishing it yet.

Mainly I've been on a quest to clean up the basement, which is full of "stuff". Today I installed the clamp storage rack I had welded up. Here's a picture of it. In the background you can see the clean half of the basement. My system is based on banana boxes and a simple database (just a text file on the PC so I can use the search function). The shelf on the right I made myself. The others I already had, but converted them to the banana box system.


Re: Alkyd paint question

#9

Re: Live and learn to store clamps

FredD

Nathan ,

I am sorry I didn't read your email , I have the email set up so if your in my address book it comes though, if not it goes into the junk mail box and sometimes I don't have the time to look though it.

I will add you to my address book right now , before I forget it.

Take care

FredD