Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Performax Belt Tracking

Posts

Performax Belt Tracking

#1

Doug in Seattle

Performax Belt Tracking

Doug in Seattle

My Performax 16-32 drive belt is giving me problems. It seems to always drift toward the motor and yoke and away from the open end. I removed the ceramic guides. Does the belt drift toward the high- or low-side of the roller? In otherwords, should I have more tension on the side I want the belt to drift toward or, away from? How much extra tension should be enough e.g., 1/4 turn on the nut or less?

Re: Performax Belt Tracking

#2

Re: Performax Belt Tracking

Dick Coers

Tension on the side that you want it to move away from. In your case, tighten the side by the motor. 1/4 turn is a good place to start, but be patient. Too agressive of an adjustment drives it away too quickly, and you end up chasing the belt back and forth.

Re: Performax Belt Tracking

#3

Re: Performax Belt Tracking

paul woolson

You might want to (potentially) save yourself a lot of headaches and check the table for square. If you remove the bolts, and the belt, put a straight edge across from corner to corner and make sure there aren't any high spots. If there are, you can shim that corner until it's spot-on. That will make the adjustments work better on the belt tension system.

Re: Performax Belt Tracking

#4

Re: Performax Belt Tracking

Dave Paine

The belt will drift to whichever side has the least tension.

When I first purchased my 16/32 I could not get this adjusted to my liking. Eventually I splurged for a new belt and this solved my problem.

If the belt is old, consider getting a new one. Not cheap though.

The belt should be able to be adjusted to track "in the middle" and not ride on either ceramic guide.

Re: Performax Belt Tracking

#5

Re: Performax Belt Tracking

Mark Mandell - Gone Round In Jersey

Paul,

Clarify what you're "squaring" please. Driven roller being square to the inside rail? Driven roller even with the table? What two elements are you squaring?

[I have much trouble with my 22-44 Pro's belt, so any insights will be welcome.]

Re: Performax Belt Tracking

#6

Re: Performax Belt Tracking

Neal in San Jose

If you do decide to replace the belt, consider ordering one from Klingspore, one of WoodCentral's sponsors. Just click on their link in the Marketplace and search their site for "conveyor belts". Their price is better than OEM, and while I don't have first-hand experience with their conveyor belts, I've been happy with everything I've gotten from them. When my old Delta's original conveyor belt finally bites the dust (pun intended), my plan is to get the replacement from them.

Re: Performax Belt Tracking

#7

Re: Performax Belt Tracking

paul woolson

Mark,

Sorry, I should have said "flat" rather than square. If you put a straight edge from corner to corner on the table, it should sit flat along the whole length. The corners should not be higher than the center and visa versa. If the table is not flat, the rollers aren't in good alignment with each other and you'll struggle with the tension forever. Does that make sense?

Re: Performax Belt Tracking

#8

Re: Performax Belt Tracking

Kirk (KC) Constable

My 16/32 Plus has never tracked properly. I've spent hours (seriously) just fiddling with it, taking it apart, replacing the tension adjuster thingies. No joy. Mine wants to move from the motor side to the outside... and that's what it's done no matter what I do (for years). Every so often I have to push the belt back toward the motor. It's a PITA, but it's become second nature to keep an eye on it, and I can move the belt with everything running, so it only take 5 seconds.

Re: Performax Belt Tracking

#9

Re: Performax Belt Tracking

paul woolson

Kirk, check the flatness of your table as I describe above. I went through 8 tracking belts before I figured that one out then it worked fine.

Re: Performax Belt Tracking

#10

Re: Performax Belt Tracking

Grant in Iowa

I would propose this:

There are three reasons the belt might tend to move towards one side:

1. driven head of the machine isn't parallel to the INFEED roller.

2. Belt is not made right

3. tracking roller (oufeed roller) is out of adjustment via the tracking screws.

The manual (like many) assumes that #3 is the only solution, and I would submit that, if you have exhausted your patience adjusting the tracking per the manual, then the trouble might be either #1 or #2 above.

You would need to make a jig to check #1, but it could be as simple as a single piece of sheet stock cut to both hook over the infeed roller and to allow a feeler guage to check the distance between that jig and the driven sanding roller. I do not know wht the acceptable tolerance should be, but it seems to me that a real issue in this area would be pretty apparent. I know on my 10/20 you can adjust this parallelism by loosening bolts that hold the head to the table.

So if your belt tracks nicely until you run a board through, you might want to check this parallelism.

FWIW,

Grant in Iowa<---if I had more time I'd draw the jig I propose

Re: Performax Belt Tracking

#11

Gotcha, Thanks

Mark Mandell - Gone Round In Jersey

Re: Performax Belt Tracking

#12

Re: Performax Belt Tracking

Bill Turpin in WNC mountains

All conveyors (belts), no matter the orientation, do this. The exaggerated wedge of the rollers is to make the concept easier to visualize.


Re: Performax Belt Tracking

#13

Re: Performax Belt Tracking

Scott Crumpton

This may not be applicable since I have the Ryobi clone which has a rubber belt. I found that through repeated attempts to get it to track properly I had inadvertently increased the tension on the belt. Once I realized this and loosened it up, setting it just barely tight enough, tracking improved dramatically. I was creating my own problem.