Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Flush-cut under crown OT

Posts

Flush-cut under crown OT

#1

Flush-cut under crown OT

Joey

I'm renovating a room's walls, but first I need to remove wood paneling. Easy enough, if it didn't have crown molding on top of it. I could pull the crown, but would probably need to replace it, since the dimensions without the paneling would grow. Here's my question, could I leave the paneling under the crown by flush cutting it below the crown? If yes, how can I freehand cut this straight line without butchering the crown? Hand tool or power tool? I'm capable of installing new crown, but you know... Joe

Re: Flush-cut under crown OT

#2

Jim DeLaney, Austintown, Ohio

Re: Flush-cut under crown OT

Jim DeLaney, Austintown, Ohio

Two methods come to mind:

1. Screw/doubleface tape shims to the bottom of a small circular saw, so it'll ride squarely on the paneling and the crown, and set the blade depth to cut just through the paneling.; or,

2. (what I'd do) use a sawblade on a Fein Multi-Master.

Jim D.

Re: Flush-cut under crown OT

#3

How big is the room? *LINK*

Bill Houghton, Sebastopol, CA

My carpenter son regularly uses an azebiki for the kind of cut you're describing (although smaller in scale). If you have less money than time and it's not a huge room, you might consider one.

I've done flush cuts like that with a small Western-type saw, but you have to kind of aggressively shove the saw into the initial cut until you've got a long enough cut for the blade to operate in. Still, if you've got a short handsaw in good shape, you could give that a try.

Remember: if you're ordering from one of Wood Central's sponsors, go to their website from the marketplace page here. Every navigation from here to a sponsor gets Ellis a little "referral" payment.


Example at Lee Valley

Re: Flush-cut under crown OT

#4

Re: Flush-cut under crown OT

Joey

Jim; I would commit to a Fein, but it has no fence for a straight line. I could sand, but that's a far cry from a flush trim bit cut for instance. Thanks for your guidance, both suggestions relevant. Joe

Re: Flush-cut under crown OT

#5

Re: How big is the room?

Joey

Hi Bill; Thanks for your input. I do have a Japanese saw, and the room is 12'X20'. I also have a steady hand. I like the limited saw dust approach. Joey

Re: Flush-cut under crown OT

#6

Re: Flush-cut under crown OT

Gary Camp, Bend Oregon

I think that I would go ahead and remove the cove. Pull the paneling down and then cut a piece of solid wood the thickness of the paneling and fasten that to the back of the cove and reinstall it. It should still fit the same, but have a cleaner edge and I would think be faster and easier than trying to make a flush cut on 40 plus feet of wall a couple of inches from the ceiling.

glc

Re: Flush-cut under crown OT

#7

Re: Flush-cut under crown OT

Joey

OK Gary; I'll reinstall it. Sounds like the best approach, since the walls are being re-plastered. I'll dry fit it, and maybe it will fit w/o the backing. Nice suggestion Thanks, Joe

Re: Flush-cut under crown OT

#8

Re: Flush-cut under crown OT

FredD

I agree with Gary about cutting off the paneling , sounds good , but is seldom satisfactory if your new at difficult , hard to reach places.

I would suggest removing the old crown and if you do it neatly and like the look of it as opposed to new Crown ,try this.

Install a 3/4" or 1/2" thick board cut a width that would project below the crown about a 1/2" or a little less and then run your old crown on that , which will need a little shortening, but a much easier way to go and you have the added advantage of it looking more like a professional crown job with the added detail which is a common way to install crown molding.

FredD

Re: Flush-cut under crown OT

#9

Re: Flush-cut under crown OT

Barry Irby

I agree with Fred. I really can't visualize a good method of cutting the paneling off and making a neat job.

To add to Fred's thought, you could use a piece of base board turned up side down and nailed to the wall as a filler. Choose a profile that complements your molding. Ogee or beaded or whatever. You could use almost any flat molding of this including door stop if you don't need much thickness. You would have two piece crown.

Re: Flush-cut under crown OT

#10

Re: Flush-cut under crown OT

John E in SC

That was my thought as well - baseboard turned upside down to make a 2-piece crown looks really good, would be minimal expense, and I think would be a WHOLE lot easier than trying to flush cut 64' of paneling above your head at the ceiling.

Re: Flush-cut under crown OT

#11

Re: Upside down baseboard

Joey

Why didn't I think of that. Because I'm a rookie. Not really, but The extra thickness will make my life easier on the re-install. Thanks to everyone who helped me avoid a time consuming ordeal. Joe