Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Baking wood to kill bugs...

Posts

Baking wood to kill bugs...

#1

Baking wood to kill bugs...

Ken Bellock (Houston, TX)

>I bought a piece of cocobolo, about 2" thick, by 4" wide, by 4' long. I then noticed it has a bunch of little 1/16" holes in several places. So I kept it separate from my main wood pile in the garage and am having it sit somewhere to see if any sawdust piles form under board. I'm nervous still having this board in my garage, and just want to make sure everything is dead in it. After doing some googling and reading old posts here it looks like 24 hours at 130 degrees in the oven will ensure all critters and eggs dead. Before I do this I just was curious how many other people here have done it and if any problems came from doing it. I'm thinking of chopping the board into two 2' sections wrapping it in aluminum foil, and then resting it on the rack in the oven for the prescribed 24 hour run at 130 degrees.

Anyone have an opinion or suggestion for killing the critters this way? My only concern is that cutting the board down and then baking it might cause it to split...

I talked to the supplier, and they said they were not aware of any live infestations in their stock. They said they had had a problem with powder post beetles in another type of wood in the past, but had seen no current activity in any of their wood recently. They also told me they didn't know if that batch was kiln dried or air dried, and that the holes could have been made before or after drying so even if it was kiln dried that didn't make it safe.

Re: Baking wood to kill bugs...

#2

Before you do that,

Keith Newton----Little Rock, Arkansas

>I have a couple of questions. Is there any sapwood, and is that where the holes are? I wouldn't think there would be any insects very interested in eating the heartwood, especially after it is dry.

If the holes are black or darker than the surrounding wood, those tunnels were probably chewed in a living tree.

IF you do the oven thing, I would keep it tightly wrapped, until it was totally cool all of the way through. Otherwise, you are likely to ruin it by causing checks.

If your parts will fit into a microwave, you can zap them in there. The waves will heat up the insects because of their moisture content without having to heat dry wood. But here again. If you heat the wood up very hot, don't let the surface dry too fast, or you will have checking occur due to quick moisture loss.

Re: Baking wood to kill bugs...

#3

Re: Before you do that,

Ken Bellock (Houston, TX)

>I do not have the piece in front of me now but I do remember that it appeared all the holes were in the sapwood, and that the holes were dark. I could take a picture when I get back home.

Re: Baking wood to kill bugs...

#4

Doug in Seattle

Re: Before you do that,

Doug in Seattle

>A guy who owns a sawmill here in western Washington State told me to use carburetor cleaner. Place the suspect wood in a large plastic bag, squirt in some carburetor cleaner and seal the bag. He claimed this would kill the bugs and not interfer with finish. I did the oven thing with some figured walnut and it all warped and twisted. Killed the bugs though. Most were in the sap wood but, some holes were in heart wood and I wasn't willing to take any chances.

Re: Baking wood to kill bugs...

#5

Re: Before you do that,

Ken Bellock (Houston, TX)

>I have read about that solution before, but also saw that that kills mama and papa, but not the eggs, and that they could pop out up to a year later and start the buffet again...

Re: Baking wood to kill bugs...

#6

Re: Before you do that,

Keith Newton----Little Rock, Arkansas

>Ken, I didn't notice earlier that you are in Houston. I seem to remember reading some time ago that there are some other type of termites down there which don't need to maintain contact with the earth like the subterranean type.

If you contact one of the exterminators that does that type, they can put your wood in a house that they are treating. If it is inside the tent, the gas will get them.

Re: Baking wood to kill bugs...

#7

Lee Grindinger

Take care with RH in oven

Lee Grindinger

>The information you have is all correct, 130f for 24 hours will kill all stages of PPBs and other borers. The problem is that ambient air heated to 130 contains little moisture and this dry air will not be good for your lumber. Wrapping it in aluminum foil will help but I'd suggest you keep a dish of water in the oven as well. Too much moisture will not damage your wood in that time while too little most definitely will. Once the time period is up let the wood breathe for a few days to reach equilibrium again,

Lee

Re: Baking wood to kill bugs...

#8

Lee Grindinger

A note about them, thar critters

Lee Grindinger

>PPBs are the bane of furniture makers because they alone have an enzyme that enables them to convert the starch in wood to glucose when the moisture content is below 12%. Sapwood has more starch than heartwood, hence the attraction. Below 10% or 11% even PPBs have difficulties slowing their life cycles down to less than half of normal awaiting better conditions.

Keith, I know that you know this but perhaps the original poster does not. The holes, if they are PPBs, are exit holes and are not indicative of a current infestation. Honestly, I'd be surprised if there were a problem now because of importing quarantines and safeguards against importing insects from other continents. If the wood is, in fact, reinfected, it most probably happened after the wood was brought into the US and it's doubtful to me the moisture content of the wood was sufficiently high to invite new visitors.

Lee

Re: Baking wood to kill bugs...

#9

Got Sun?

Mark Mandell - Gone Round In Jersey

>130� isn't hard to reach and hold on a bright sunny day in Texas by wrapping your wood in black plastic and sealing it with plastic tape. You can go one step further and run some car exhaust into the "bag" before you seal it. Never tried it with cocobolo, however in worked on cherry in New Jersey. I'd leave it sealed and out for several sunny days. You can check how hot it gets with an instant-read meat thermometer.

Re: Baking wood to kill bugs...

#10

Re: A note about them, thar critters

Yonak

>Lee, why do you say the holes are exit holes ? Do the holes indicate there is not an infestation any more ?

Re: Baking wood to kill bugs...

#11

Lee Grindinger

The life cycle of a powder post beetle

Lee Grindinger

>Powder post beetles begin life as an egg laid in the pore of wood, a very tiny egg virtually invisible to the human eye. The larva hatches and burrows into the wood where it lives for several months to over a year depending on how optimal conditions are. Once ready to pupate the larva finds it's way to the surface of the wood, pupates, and flies away as a short lived adult. It hooks up with the opposite sex for a night of frivolity, lays eggs in an appropriate wood pore, and dies. Appropriate wood pores must have adequate moisture content to make ma and pa believe the larva will thrive and while they often select the same species eggs will not survive in wood with too little moisture, below 10%.

The holes are exit holes of the larva just before they pupate and the frass, the powder that falls from the holes, is digested wood tissue.

Of the three beetles commonly described as powder post beetles only one, the anobiid, has the enzyme that enables it to convert the starch to sugar in low moisture wood. There are 3 beetles commonly called PPBs, but only one is actually a PPB, the Lyctid. The anobiid is also known as the Deathwatch Beetle and the Furniture Beetle.

I hope this answers your question, :D

Lee

Re: Baking wood to kill bugs...

#12

way too extreme

Bill Tindall

>It is my understanding that this species is difficult to dry, so if you were to heat it quickly it would probably crack.

I doubt that what ever makes holes in this stuff is native to a northern climate and I suspect it is long since dead. But to be sure, paint it with any solvent, lacquer thinner being best, wrap in plastic while still wet and let it sit a day. All the solvents are more or less toxic to bugs. Be cautious about flammability issues.

Re: Baking wood to kill bugs...

#13

PS

Bill Tindall

>mothballs ok too but I would leave it two days as they make fumes slower.

Re: Baking wood to kill bugs...

#14

Lee Grindinger

Re: way too extreme

Lee Grindinger

>Bill, is there any evidence that this works other than anecdotal evidence?

Re: Baking wood to kill bugs...

#15

no

Bill Tindall

>There is no question that the solvent vapors will kill any insect. The only question is whether these vapors will diffuse into the holes the critters bored. There is good reason to expect the vapors will penetrate any physical opening. The solvent molecules will diffuse through air at a rate of around cm/sec, so it should not take long for a lethal concentration of vapors to reach within the holes starting with a layer of solvent liquid on the lumber surface. I have sprayed larger quantities of actively infested lumber with malathion and killed them with the vapors of this chemical. Of course it will take a much lower concentration of this bugacide than something like acetone.

I presume these bugs need oxygen, so another way of looking at the situation is that if oxygen can diffuse into where they are at so can a solvent vapor.

Re: Baking wood to kill bugs...

#16

Bill, I would not count on lack of oxygen

Keith Newton----Little Rock, Arkansas

>doing the trick. On one of my vacuum pumps, I have a moisture separator, which is just a mayonnaise jar, which has a lid that has an intake port, with a filter in the middle, which leads to the exit port.

One evening when I knew I would be running the pump for most of the night, I went out and caught one or several insects species. I felt like some demented scientist as I watched them scramble around in a panic as the air got thinner.

Well, all activity had stopped by the time it reached full vacuum, or 28" Hg. But in the morning, I dumped them out on a table by the office door. They all seemed to be dead, but around lunch, as I walked by, I thought I saw the leg of the cockroach twitch. Well, that stopped me in my tracks, and sure enough, after watching about 20 seconds, I saw another twitch. I then picked up a little stick to touch and stimulate it.

It didn't take long before it was ready to run for cover. I guess they are like seeds that germinate after dormant spell.

Now, I have contemplated putting insect infected wood in a vacuum bag, then drawing a vacuum for a spell, then letting the bag and the wood inside fill with some kind of gas, rather than air after I shut the pump off. The vacuum should pull a gas into the cells for full penetration.

Re: Baking wood to kill bugs...

#17

Re: Baking wood to kill bugs...

john lucas

>Put the wood in a plastic bag and put moth balls in it. that worked for a friend of mine.

Re: Baking wood to kill bugs...

#18

Re: Bill, I would not count on lack of oxygen

Barry Irby

>Wow. I would have thought that a vacuum for eight hours would have killed them. Whoda thunk it?

I once held a horse fly under water about ten minutes and when I released it, it flew away as if nothing happened.

You can kill the insects with Methyl Bromide or Viacane if you can get any. These are the chemicals they used to use to gas houses for powder post beetles. Be Extremely careful if you decide to try this. They are deadly poisons and will kill YOU just as easily as they kill the bugs.

You could also use Bora Care, but I am not sure it will penetrate cocobolo. It does a fine job on pine, just don't know about Cocobolo.

The other think to worry about is the residual effects of any chemicals you might use. I think the solvents like lacquer thinner will completely evaporate and be gone, leaving none in the wood, but the others will leave residue..

Re: Baking wood to kill bugs...

#19

Gas

Mark Mandell - Gone Round In Jersey

>A chunk of dry ice in the bag should do the trick

Re: Baking wood to kill bugs...

#20

Re: The life cycle of a powder post beetle

Yonak

>Yes, Lee. That was very informative to me and I appreciate the primer. Based on you knowledge, would you say it would be a fairly safe bet that a large stack of wood that has been stored indoors for several years, some boards of which have worm holes, would be free of active infestation and no new boards would be infested ?

Re: Baking wood to kill bugs...

#21

Lee Grindinger

Questions

Lee Grindinger

>Was the wood kiln dried? Air dried? Where do you live. roughly? When you say "inside" do you mean a garage, basement, living room? What is the average humidity and temperature where the lumber is stored?

If the lumber was kiln dried and never stored in wet conditions it's safe from bugs.

It's all about EMC, equilibrium moisture content which will tell us how much moisture the lumber is likely to have.

At the end of this article, http://www.woodcentral.com/articles/shop/articles_377.shtml is an EMC chart that will tell you the likely moisture content of the lumber, if it's below 10% after 3 years you can be sure there is no infestation. Below 10% anobiids go into a semi-dormant state lengthening their larval stage to over a year if necessary but 3 years will be beyond even their resourceful constitutions.

Re: Baking wood to kill bugs...

#22

Re: additional info

Yonak

>Was the wood kiln dried? Air dried?

air dried indoors

Where do you live.

Georgia

When you say "inside" do you mean a garage, basement, living room?

The building is fairly newly built. It has a slab floor and is not heated. When the wood was first put in I had dehumidifiers or fans running. It is stacked and stickered, the first level 3 1/2" off the concrete floor.

What is the average humidity and temperature where the lumber is stored?

In the summer is gets very warm in the building (it has glass panels in the roof) .. daytime temperatures often greater than 100� inside, but a power roof ventilator keeps it from getting extremely hot .. winter temperatures at night mostly in the 30s. Relative humidity levels where I live average from 50% to 90%.

The wood was cut from logs that sat out (a few, likely, directly on the ground, which is probably where the bugs came from) for a few weeks to a few months, then put into the building after sawing.

I never checked the wood moisture level, but my guess is 12% ~ 14%. It has been stacked and stored for about 4 years and has not been exposed to moisture, with the exception of air humidity, during that time.

Re: Baking wood to kill bugs...

#23

Re: Baking wood to kill bugs...

r payne

>Mothballs in a bag haven't worked for me.

ron

Re: Baking wood to kill bugs...

#24

Lee Grindinger

Can't be certain, but

Lee Grindinger

>I can't be certain, but I'd say you're alright. It certainly is not an environment PPBs would thrive in and in Georgia there are better options for them out of doors. So, unless you have reason to believe there is a problem I'd say assume there is not. Look for expired adults (Google Anobiid for images) and unless you find some don't worry about it.

Re: Baking wood to kill bugs...

#25

Thanks

Yonak

Thanks for the assessment, Lee. This is a question that's been sort of nagging at me for quite a long time, but not such that I was going to go about having all the wood unstacked and kiln dried. I will find out for sure if there is a widespread problem when I begin to pull down and plane the wood. You've set my mind at ease a bit. Thanks.