Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Old router

Posts

Old router

#1

Old router

Jay

>I recently attached my P-C Model 690 router to the router table I build. In order not to have to dismantle it each time I need a router, I just picked up a P-C (US made) 100-M Motor (115 V; 6.5 amps). It was a very good deal so could not resist. I have now dismantled it and the copper wire connecting 1 of the 2 carbon guides (bushings?) is disconnected so I will re-solder it (the spring is OK), however the guides/bushings appear quite worn. Is this dangerous? Can I find replacements easily? Also am I cruising towards a potentially unpleasant/dangerous situation if I don't replace them? Everything else appears in good order (collet is tight, etc.).

Would appreciate some knowlegde from anyone that knows routers from the guts up.

Thanks, Jay

Re: Old router

#2

Re: Old router

del schisler

>i have 5 routers and do a lot of router work You can get new 690 parts I would do that You don't want the bit to come out when routing Play it safe I have 2 of the 690 routers and they are good work horses Get the parts good luck here is the link for parts and another link that has lot's of router stuff I have their table this is the best site for router stuff

http://us.oak-park.com/catalogue.html?list=RT01--

http://www.ereplacementparts.com/porter-cable-parts-c-129.html?gclid=CPHhz7-29Z8CFSJ25Qod6hrBfA

Re: Old router

#3

Re: Old router but Good Router

George@Colonel's Workshop-Havertown PA

>Good Afternoon Jay,

I assume you will be using the 690 in your table. I used one of mine under the table for 95% of my work for sefveral years. At 10 amps, I never had a power problem, and the collets could handle both 1/4" AND 1/2 " SHANK BITS.. I think the PC-100 motor is not strong enough at 6.5 amps for table worrk, but should be fine for hand held edging and inlay work. Aren't you restricted to 1/4" diameter bits with that machine? I suggest you put it in fully restored mechanical condition. Parts should be readily available from Porter+Cable.

George

Re: Old router

#4

Re: Old router

Jay

>Thanks Del. I will check out the web-sites and as you correctly say "play it safe". Jay

Re: Old router

#5

Re: Old router but Good Router

Jay

>George,

You are correct about the 690 being attached to my router table and the 100 being for hand-held use (you are also correct about it being for 1/4" bits only). I have taken it apart and other than the brushes, appears to be in good working order. I will check out both your and Del's suggestions as to web-site sources for replacement brushes. Appreciate the guidance. thanks, Jay

Re: Old router

#6

Re: Old router

Don Orr

>Hi Jay,

If I read your post correctly, the carbon "guides" you talk about are actually the commutator brushes and are designed to wear away over time and be replaced easily. Instead of soldering it, it would be very easy and relatively cheap to get a new set which should last you quite a while. No sense in fixing bad parts, in my opinion, that are meant to be replaced anyway.

Years ago when I was selling PC tools in a hardware store, PC had a flat rate repair program where no matter what was wrong with a PC tool it would not be more than a specific maximum price to rehab/repair that tool. They had a schedule of prices for each tool so I could tell customers how much it would cost for the repair job in advance. They would go over the whole tool and put back into like-new condition and only charge the flat rate no matter what was wrong. Usually way cheaper the the cost of buying new tools. I don't know if they still do that but it can't hurt to ask. Now that the have sold out to another company (and I do mean sold out!), I doubt they have a program like this anymore.

Enjoy your new toy!

Re: Old router

#7

Flat Rate Repair

George@Colonel's Workshop-Havertown PA

>Good Morning Don,

My latest P+C 690 motor had problems which I discovered when I went to buy it used. The seller wound up giving me the machine, and I took it to the local P+C/DeWalt service center. They overhauled the entire machine for about $75.00. I stuck it in my plunge base and am living happily ever after. I think what I paid for the repair was a "full" price. However, they did put it in first class condition, and $75 for a perfect 690 seems like a very good deal. When I initially turned it on, I heard bearing noise, so told the seller to keep it. He was embarrassed, apologized, and handed it to me, saying I could always use an extra 690L base. ;)

George

Re: Old router

#8

Re: Old router

Jay

>Thanks Don. Problem I am facing is that the PC 100M is discontinued,

and I'm having a tough time finding a source for the brushes. I will

contact PC directly and find out (a) if they still run the program you

mention (not holding my breath for that one) and (b) if they have the part.

Re: Old router

#9

Re: Old router *LINK*

Bill Houghton, Sebastopol, CA

>I don't know that the brushes for the Model 100 router have changed much in its various incarnations. You might check E-replacement parts (link below). Call them to ask.

Failing that, I bet Dick Jarmon (dickj@wowway.com), who is the major source for older Porter-Cable parts, will have them.


http://www.ereplacementparts.com/

Re: Old router

#10

Thanks Bill !

Don Orr

>That right there is some real good information to have handy !

Re: Old router

#11

Re: Old router

Jay

>Thank you Bill. I've been onto E-Replacements - very helpful people (good find) and they have made several suggestions including some of the same one's made by other contributors to WoodCentral (e.g., Ohio Carbon Brush). I will email Dick Jarmon and ask.

As an aside, I remain somewhat in awe of the knowledge base of the participants to WoodCentral and the pleasure you seem to get from sharing it.

Best, Jay