Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Tablesaw Surface Question

Posts

Tablesaw Surface Question

#1

Tablesaw Surface Question

Steve in Phoenix

>I've noticed some very minor pitting. I don't want to make it sound severe, it's actually quite minor. And I'm not sure if it is new or if I have just noticed. It looks like pinholes that are dark inside. Very small. I wanted to do a somewhat annual reapplication of paste wax protection, but is there something I should do about what I am seeing? I would usually wipe the top down with steel wool and mineral spirits as preparation.

Thanks

Re: Tablesaw Surface Question

#2

Re: Tablesaw Surface Question

Bill White

>Wax it well with a good paste wax, buff it, and enjoy. Don't get too hung up unless there is some ongoing deterioration.

Bill

Re: Tablesaw Surface Question

#3

Re: Tablesaw Surface Question

Steve in Phoenix

>Thanks Bill.

Do you have an opinion on rubbing in talcum powder prior to waxing?

Re: Tablesaw Surface Question

#4

JL

Re: Tablesaw Surface Question

JL

>Talcum powder is about as "mild" an abrasive as you can get.

For minor rust and surface crud removal - try a piece of aluminum foil. Put a couple of drops of water on either the metal or the foil. Scrub the surface. Wipe with a damp cloth or paper towel. Dry. It gets a fair bit of rust and crud off. I didn't believe it would work - until I tried it.

Re: Tablesaw Surface Question

#5

Re: Tablesaw Surface Question

John in NM

>You didn't mention how new the saw is. I wouldn't give those pits a second thought, they're probably remnants of the rough cast surface that weren't entirely machined off, or if the saw is an old one, perhaps old rust pitting. Neither will do any harm or affect the use of the saw.

As I understand it, talc is used in place of wax, being faster to apply. I use wax because I always have it around, and because I dislike my shop smelling like baby powder ;D

Re: Tablesaw Surface Question

#6

Re: Tablesaw Surface Question

Steve in Phoenix

>The tablesaw is about 8 yrs old, and has a very smooth surface. We just moved to a side of town that is considerably damper than where we used to live. Something to do with being hemmed in between mountains I think. Also alot of grass in the neighborhood getting watered. The garage is not as sealed up as my last one. So I think these new conditions are having an effect. The tablesaw sees the most use and must have had its wax mostly worn off as the other machines do not seem to be affected.

I've always had trouble with the application and buffing of the wax. I seem to apply too much to be able to hand buff. Maybe warm up the wax or iron or both?

Re: Tablesaw Surface Question

#7

Re: Tablesaw Surface Question

John in NM

>With no coating of surface rust, I can guarantee there's no on-going pitting occurring. I don't think you have much to worry about in the Arizona climate - Florida might be another story. I have an old jointer that has moderately severe pitting on one end of the infeed table. It looks to have been stored outside and ineffectively tarped, and must have been rained on for years. As long as there is not active rusting going on, this is really just a matter of cosmetics. Wax it and forget about it.

You could try adding a little solvent to your wax, that might help get a thin, even coat to be buffed out. I only use wax to reduce friction on the top, its not much of a protective film IMHO, and cast iron doesn't need a whole lot of protection. Wax will help prevent the nuisance oxidation, but will quickly wear off under normal use. If you get a little surface rust during the monsoon season or an abnormally wet winter like the current one, just buff it off with some steel wool and re-wax.

Re: Tablesaw Surface Question

#8

Re: Tablesaw Surface Question

Steve in Phoenix

>Thanks John. I don't think I need to break out the Naval Jelly just yet!

Re: Tablesaw Surface Question

#9

Glad to help!

John in NM

Re: Tablesaw Surface Question

#10

Re: Tablesaw Surface Question

FredD

>I like many have tried a host of lubricants, Steve and one time many years ago a old timer told me about using Talc or Cornstarch, Never have looked back , keep a can handy to the Saw and Jointer and Planer.

Quiet some time ago one of the Wood Magazines did a little research on that method and concluded the Talc or Corn Starch actually fills the pores in Cast Iron.

But like all of the rest of the lubricants , you need to form a habit in using it.

Talc or Corn Starch is merely a friction reducer and will not help with oxidation issues.

FredD