Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Wood Storage Rack

Posts

Wood Storage Rack

#1

Wood Storage Rack

Ed Wesolek

>Hell-o Everyone,

I am making time this weekend to build my wood storage rack. The area that I have to work with is about 12' tall by 9' wide by 16' long. I have rough sawn boards of different species. The lengths are any where from 18' to 8' long as well. I am thinking that I might want to build this rack so that I can place some cheap 1/2 plywood down between the supports to help keep the wood flat and not bow. So that means either 2' on center or 4' on center. What do you think would work the best, and or other ideas?

Thanks for your input as it has been very useful over the years.

Ed

Re: Wood Storage Rack

#2

Re: Wood Storage Rack

Brent Smith in Montreal

>Hi Ed,

The supports on my rack are placed a 2', and I use 3/4" ply as a shelf. 1/2" at 4' would be useless considering the weight of the lumber placed on it, especially if it's stickered causing the weight to be on a single point.

Re: Wood Storage Rack

#3

JL

Re: Wood Storage Rack

JL

>Obviously you will have to saw the 18' boards.

I let most of my wood "self-support". My racks in my shop are at either 30" intervals or 4' intervals. The racks at 30" are to support leg blanks at a convenient height. The 4' is between my sets of racks.


This was an old "clean" shot - nowadays the bottom supports are supporting some 12' pieces of oak and poplar.

Re: Wood Storage Rack

#4

rack experience

Bill Tindall

>1. 4' spacing is fine unless you intend to store lumber less than 4' in the same rack as the long stuff... a bad idea. Make a separate rack for shorts with 2' spacing.

2. Rack made from "ladder shaped" supports work fine. There is no need to put any plywood on the bottom. Hardwood lumber is very stiff in a pile. A vertical support consisting of a 2 x 4 and 2 x 4 horizontal supports is fine for up to 4' wide compartments. see picture.

Re: Wood Storage Rack

#5

Re: rack experience

Ed Wesolek

>Hell-o Everyone,

Thank you for the replys to my question as they did answer my question for both the long boards and the shorts boards that I have. I will post a picture when I complete my project.

Thanks again.

Ed

Re: Wood Storage Rack

#6

Re: rack experience

Alan in Little Washington (NC)

>How about a different approach?

How will you examine (both sides), select, and remove boards you need? It is almost impossible to do in a horizontal rack, especially boards at the bottom of high stacks.

While you will be limited to 12" boards, how about a vertical rack? It takes much less material and is easy to install. The floor, not arms support all the weight. By stacking the boards with edges to the wall you can inspect both sides easily. If it is good enough for Sam Maloof, David Marks, Lon Schleining and other noted woodworkers and Woodcraft, it is good enough for me.


img

Re: Wood Storage Rack

#7

Re: Wood Storage Rack

Grant in Iowa

>Ed,

I designed and built this rack for use in my old shop to store lumber as described in Articles:

http://www.woodcentral.com/articles/shop/articles_794.shtml

I have since moved, taking that rack with me to install along the wall in my new shop and have also built another one based on the same basic design. The new one is a free standing A-frame version (thanks for the idea, Ellis!) with sheet goods storage incorporated.

here's a photo of that rack:

http://www.facebook.com/photo.php?pid=1010929&id=1044178062

I find the shelves make lumber easy to sort and access with a short step ladder. They are very sturdy. I suggest drilling holes in the uprights about every 8" or so in order to allow flexible shelf sizes.

The tilted back design helps keep things from falling off, and also keeps the center of gravity over the base regardless of how you load it.

Regards,

Grant in Iowa

Re: Wood Storage Rack

#8

Ellis Walentine

Couple things

Ellis Walentine

>Um, Grant...

I'm sure your wood rack is a dandy and I'd love to look at it, but the link you posted brings up a Facebook login page, and I don't have a Facebook account. I'm wondering if you would mind registering a profile and then uploading your photos directly to the messageboard. Also, without a registered profile, any posts with "http://" in them (links), are kept in quarantine until approved by a moderator, which isn't always right away.

Anyhow, I'd really like to see the photos if you'd put them somewhere that I don't need to be a Facebook member to access.

Thanks,

Ellis

Re: Wood Storage Rack

#9

Re: Wood Storage Rack  II *LINK*

Grant in Iowa

>OK, now that I am registered again...sorry...

Ed,

I designed and built a rack for use in my old shop to store lumber as described in Articles (see below link).

it is a nice rack, designed to be mounted to a wall, while not putting too much pressure on that wall (thus the angled design placing the center of gravity over its base).

Now, Page 2:

I have since moved, taking the above described rack with me to install along the wall in my new shop. I have also built another next to it one based on the same basic design. The new one is a free standing A-frame version (thanks for the basic idea, Ellis!) with sheet goods storage incorporated.

here's a photo of that rack:


I find the shelves make lumber easy to sort and access with a short step ladder. They are very sturdy. I suggest drilling holes in the uprights to receive the pipes about every 8" or so vertically in order to allow flexible shelf sizes. I made this A-frame rack 8' long with 16" centers.. which I have decided is a bit overly built...perhaps 24" centers would be plenty.

The tilted back design helps keep things from falling off, and also keeps the center of gravity over the base regardless of how you load it. In times when you don't have a lot of lumber on hand, you can load the lumber higher (judiciously) and remove the pipes on lower shelves to provide extra space for other things.

I buy the pipes precut at a local steel supplier. They are 1/2" black iron and vary from 16" long on lower shelves to about 22" long on the upper shelves to save floor space. I think the entire project cost me about $270 three years ago and stores around 2000 board feet of lumber.

The added upright at the top is a series of 2x4"s I added with heavy duty (not deck) screws to allow more lumber to be stored. The main uprights are joined at the top with two 3/8" carriage bolts per a-frame. Don't put this type of thing together without using heavy hardware!

I should add that not pictured is a sheet of plywood on the inside of the a-frame and screwed to each a-frame to prevent the assembly from racking.

See the below link for construction details and hole size, etc... the link is for the wall leaning version, but it should give you the idea. I don't have a plan for the a-frame version but you should be able to figure it out from the photos.



Regards,

Grant in Iowa


Grants lumber rack in articles section