Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Wall Cabinet

Posts

Wall Cabinet

#1

Wall Cabinet

Don M

>I am planning to make a very basic wall cabinet for my shop. It will be 7 1/2' X 30". It will be made of 3/4 birch plywood. All joinery will be with #20 biscuits. The cabinet will have one horizontal shelf running its entire length which will divide the cabinet into an upper and lower section. Each section in turn will have to vertical divider panels that will result in a total of 6 large cubby holes, 3 on top and 3 on the bottom.The back will be a piece of plywood that will be rabbited in so that it is flush with the sides.It will be glued and nailed to the sides and top and bottom and finishing nails will be driven along the horizontal shelf as well. The cabinet will be hung on 2 cleats, each about 5' long one at the top and the other near the bottom. The cabinet will carry a fare amount of weight probably near 200lbs.

I was planning on using 1/4" plywood for the back, is that enough or should I go to 1/2"?

My concern was the back being pulled off.

Thanks for the input.

Don M.

Re: Wall Cabinet

#2

Re: Wall Cabinet

Mark Mandell - Gone Round In Jersey

>Since you're making "cubbies" anyway, I'd suggest you break up the beast into 3 sections; not only stronger that way, but also way easier to mount on the wall without a crew. Using 1/4" ply, you should inset your the back a full inch, then use 3/4"x2" pieces at the top and bottom to reinforce the ply and serve as your fixing points. The bottom cleat will take most of the weight, so the top fixing is mostly for balance. 200 lbs in a 8' cabinet is no big deal.

Re: Wall Cabinet

#3

Re: Wall Cabinet

FredD

>Don,

if your using nailers at the top and bottom , 1/4" wil be fine.

I have many times seen customers overload upper cabinets with canned goods and they had 1/4" backs.

When I was a barely a Carpenter, we installed Cabinets in a subdivision that a extremely over weight woman had overloaded , then while getting a item down from the upper , had the stool slip, grabbed the Cabinet and yanked the entire mess down on top of her all the way to the floor.

Chet Spiering the contractor had his Engineer photo the Cabinet back still nailed to the wall with 16D nails and he nearly kissed us because the accident went to court and the Engineer testified that the nailing schedule was more then required and the accident was entirely the Woman's misfortune ,brought on by the overloading of the Cabinets.

The suit was dismissed.

FredD

Re: Wall Cabinet

#4

Re: Wall Cabinet

Don M.

>Could you please explain what you mean by "nailers"?

Thanks

Re: Wall Cabinet

#5

Re: Wall Cabinet

Andy Lincoln,in Dearborn MI

>Don,

i am not trying to speak for Fred but typically in a cabinet we will shorten(in depth) the interior partitions by 1" and install a 1/4 back panel that is inset by 3/4" from the back.This resulting space gets filled with 2 horizontal blocks(nailers) that are the width of the interior of the cabinet by say 3" wide.

i will glue,nail,screw,staple these to my cabinet sides and 1/4" back.It is then thru these nailers that the cabinet is screwed into the wall studs.An alternative to this would be to rip a bevel on the top nailer and make a matching cleat,a.k.a. french cleat that you can place on the wall and then by mating the opposing bevels hang the cabinet and secure with a couple screws.

note my sketch is very crude and quick.

Andy

Re: Wall Cabinet

#6

Re: Wall Cabinet

FredD

>"Don,

i am not trying to speak for Fred "

Any time you feel like it Andy , be my guest ;-))

I slightly disagree with the need to reduce the interior depth of a upper cabinet by a inch for this reason.

I typically cut tops, bottoms and sides of upper cabinets to a 11 and 7/8ths inch depth to take full advantage of a 4 by 8 sheet of plywood.

Reducing this by a inch such as you describe reduces the interior space by nearly ten percent.

I have also found that a nailer top and bottom seems to work well over the years even with a Wood Institute set of specs.

I probably also think that overdoing on things that support a dead load and where you have no control over the amount of that load is not a bad idea.

Cheers,

FredD

Re: Wall Cabinet

#7

Re: Wall Cabinet

Don Messick

>Andy,

Thank you very much. I get it now.

Don M,

Re: Wall Cabinet

#8

Re: Wall Cabinet

FredD

>Don ,

excuse me for not reading your request about Nailers, it is like Andy says , it's a Cabinetmaker term for a wood strip top and or bottom inside a upper cabinet and you "nailed though" it in the days before screws became fashionable.

I used a "Peashooter" I had made by a Blacksmith which is a 1/2" G.I. pipe with a steel rod inside of it with a weight on the end to hold it by and drew back the rod to strike a nail you inserted into the pipe.

My weight is a Spanish Cannonball dug up in a foundation trench along with ten others like it and about four hundred years old.

This was across the street from the Mission San Jose in Fremont , Ca where I remodeled and added to a home for Art Brown

The beauty of the "Peashooter " was that it allowed you to stand in the middle of the Kitchen and nail the upper to the wall, no ladder, stool or step needed.

Years later somebody took the idea which wasn't mine by the way , and manufactured them to sell in hardware stores.

Of course, the Cannonball had been replaced by a crappy looking weight.

FredD

Re: Wall Cabinet

#9

Re: Wall Cabinet

Don M.

>Thanks Andy the sketch was great.

Don

Re: Wall Cabinet

#10

Re: Wall Cabinet

Don M.

>Thanks Fred,

I get it now

Don

Re: Wall Cabinet

#11

Re: Wall Cabinet

Barry Irby

>You could cut the bottom edge of the upper cleat at an angle and turn it into a French cleat. Install a matching one on the wall and hang the cabinet from that. Then you could "over nail" the climate and it would not show. And you could move the cabinet later easily. If you felt it were important you could do the same to the bottom cleat or just drive a screw or two through it.

If you don't want to do the French cleat, you could move them inside the cabinet and then you would only lose the volume of the cleat with no air space behind the back.

If the back of the cabinet is flush to the wall, you could lick it and stick it to the wall like a stamp. ;)