Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Even out oaks colors

Posts

Even out oaks colors

#1

Even out oaks colors

Stephen Kirk in Quakertown Pa

>I'm getting ready to finish an oak table top. My boards range from slightly red to a bit brown. What is the best (or easiest) way to finish so the color is even. Is it possible to keep the color somewhat light too?

Re: Even out oaks colors

#2

Jason Roehl in Lafayette, IN

Re: Even out oaks colors

Jason Roehl in Lafayette, IN

>Maybe others will chime in with some other solutions, but here's my take on it.

You're talking about using some sort of light stain or dye. Those will likely not even out the color much because a light stain or dye will be very translucent, letting much of the wood's natural color through. The only real way to keep it light and get consistent color will be to begin with boards that are pretty close in color to begin with. Red oak does have a range of colors to it, and some people like that variation, but I don't care for it in panel/table top glue-ups.

Jason

Re: Even out oaks colors

#3

Re: Even out oaks colors

Stephen Kirk

>Here is the top I am dealing with. A bit of variation to deal with.


Re: Even out oaks colors

#4

Suggestions

Mark Mandell - Gone Round In Jersey

>The flat-out easiest is to give the raw wood a good exposure to strong sun. While not as photo-reactive as cherry, you're likely to see some change off the oak's salmon color. If you're concerned about the brown ones going darker, mask them off with tape and dark paper or cloth (not plastic!).

I've never tried to tone-shift individual boards in a top using finish, preferring instead to color match before glue-up like Jason.

The dead-sure way to match them all is, of course, to bleach them out to "white" then dye back up to the even color that you want.

Re: Even out oaks colors

#5

What I do

Bill Tindall

>

something strange happened when I browsed the PIC file; not sure what is going to become of the attached PIC

I think you will find that when the sun light works on the oak that it will all become very similar. However, I always stain oak. I like a yellowish brown tint. I use anybody's oil wiping stain, for example Minwax. Any store worth buying from will let you dab samples on an oak board to see what it looks like.

We had a raging discussion of staining on the hand tool board a while back and I think my recommendations became accepted by those that tried them.

Step 1. Meticulously sand the piece spending most of your time with 100 grit, then follow with 120, and finally 180. I start with an air driven ROS sander and then hand sand the 120 and 180. If I was successful in using some other machine to sand with I would, but I haven't. They all, in my hands , leave scratches of one sort or another that show up when I stain.

Lack of satisfaction staining generally is a result of poor sanding. You are done with the 100 grit when all the planer marks are gone and there are no dull places indicating torn grain and not apparent scratches or swirls. Places are dull because they are catching saw dust. If they catch saw dust they will catch stain and become dark resulting in the dreaded "Blotchy Look". A card scraper is a good means of removing torn grain; much faster than sand paper or even a belt sander.

Step 2. Make a "rubber" or "tampon" like is used for shellac application. It will be a golf ball sized wad of cotton, cotton cloth, or sheep wool and then wrap a cover of cotton or linen over the ball and secure with a "twistie" or string or just twist and hold it. It will look like a badminton bird. Dab the bird in the stain picking up a bit and rub it on the wood. Dab and rub building the color until you like it. If you want the pores dark, as most do, then you will need to get the bird fairly wet and squeeze the stain into the pores.

You can do this step with a brush, slathering on stain and wiping it off but this approach is most wasteful of stain and the color depth will be what will be, without the ability to control it.

Step 3 Clean up with a clean cloth and let dry before top coating.

Re: Even out oaks colors

#6

It's beautiful as is

Clint Searl, at the base of Haycock Mountain

Re: Even out oaks colors

#7

PS

Mark Mandell - Gone Round In Jersey

>Stephen,

From your pic I have to wonder if part of your color difference is partly due to chatoyance and grain direction as I note the lighter section on the direct opposite location. I'ma betcha da sun will do you well. :)

Re: Even out oaks colors

#8

Re: It's beautiful as is

Stephen Kirk

>Thanks! It's good to hear that from time to time.

Re: Even out oaks colors

#9

Re: It's beautiful as is

Clint Searl, at the base of Haycock Mountain

>No offense intended, but real even color is available with Formica. I tend to favor the variations among boards. Celebrate wood in its many personalities.

Clint

Re: Even out oaks colors

#10

an issue if you don't stain

Bill Tindall

>Many coatings yellow as they age. While yellowing is not a problem on walnut and cherry it could be on oak. If you "brown" up the oak with a bit of stain the yellowing will not be a problem. Any of the common urethanes yellow more or less with some much more than less, the alkyd varnishes yellow some, while the acrylics stay clear.

The oak will become browner with age and darken substantially from what you have now.

Re: Even out oaks colors

#11

I use golden oak stain look's good to me 

del schisler

Re: Even out oaks colors

#12

Re: an issue if you don't stain

Stephen Kirk

>Ah, good to know. Finishing is one of my areas to improve on.

Re: Even out oaks colors

#13

learning curve

Bill Tindall

>Finishing is no different from any other aspect of woodworking- there is a lot to know/learn and it needs to be practiced. It appeared that you have the skill and experience to have done a nice job on the top. The same amount of care needs to be applied to the finishing. BTW, practice on something other than the top.

If you like lighter shades consider ash. It is one of the few woods I finish natural and I use it when I want a light appearance. Even ash turns a light brown with age. Don't use a yellowing finish on ash or it looks awful.