Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

reply to Mark Mandell about drivebelts on a Unisa

Posts

reply to Mark Mandell about drivebelts on a Unisa

#1

reply to Mark Mandell about drivebelts on a Unisa

Fred Davis

>Hey Rick,

Everything I've read over the years seems to maintain the "rule" that you can't properly transmit more than a bit over 1hp on a single belt drive, and that's why multi-belt (and now poly-v belt) drives are used for 3-hp and up machines.

Is this incorrect

Yes Mark you are correct.

I suggested to the original poster that he contact the people at Delta for accurate information.

A couple of days ago this came up and I didn't have the time to contact Delta Technical service in Jackson , Mississippi. I emailed them and a Engineer by the name of Fred called this afternoon .

Fred said any saw motor over 1-1/2 HP needs Multiple belts , so the the Three and Five HP Unisaws have three pulleys for this reason.

Matched set belts are recommended for not only same size by cutting them from the same sleeve , but they maintain that size as the belts warm up and gradually wear evenly, which may not be the case with mixed sleeves or brands.

His follow up email was sent by his Secretary.

"Recently you requested personal assistance from our on-line support center. Below is a summary of your request and our response.

If this issue is not resolved to your satisfaction, you may reopen it within the next 5 days.

Thank you for allowing us to be of service to you.

To update or reply to this message:

1. Press your "Reply" button.

2. Place your cursor in the space indicated below.

3. Type your response.

4. Press your "Send" button.

Subject

why does Delta use three belts on their Unisaw ?

Discussion Thread

Response (Stephanie Riddick) 01/04/2010 05:18 PM

Dear Fred, we believe the following information addresses your inquiry.

To effectively transfer more than 1 � horse power through a belt and pulley system, a multi grove pulley must be used.

Thank you for allowing us the opportunity to serve you. If your question remains unresolved or if you require additional information please update this incident.

Sincerely,

Fred

Customer (Fred Davis) 01/01/2010 03:08 PM

This question has popped up on WC forum concerning the number of belts needed for a Unisaw.

A self described expert says they are not necessary and the only reason Delta uses a three belt pulley is and he says " folks would be scared if they didn't see that the machine had three belts".

My question is ,, is any of the above true?

Thank you for your attention.

Fred Davis

Question Reference #100101-000074

Product Level 1: Table Saws

Product Level 2: Stationary

Product Level 3: Unisaw

Category Level 1: Delta

Date Created: 01/01/2010 03:08 PM

Last Updated: 01/04/2010 05:18 PM

Status: Solved

Re: reply to Mark Mandell about drivebelts on a Unisa

#2

Re: Drivebelts

Mark Mandell - Gone Round In Jersey

>Fred,

I did a bit of research myself. Called a PE who I've used as an expert, and posed the question.

His first response was "You want the long or the short answer?"

I replied, "The free one."

He said "Depends."

"On what?" I asked.

He said "Thought you wanted 'Free'."

He then explained that belt drives' power transmission ability is a function of the size of the pulleys and the belt. The smaller the pulley, the less power can be transferred in a single v. So the Unisaws and clones, with their small 3" pulley sets, need 2 or 3 belts to carry the motor power efficiently, but my 3hp IR compressor with its 12" pulley, is quite happy with only one.

Guess we were all correct, but the complete answer was more complex.