Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Steam bending chair posts - suggestions?

Posts

Steam bending chair posts - suggestions?

#1

Steam bending chair posts - suggestions?

Joe in a Cleveland Suburb

>Hello.

I am making ladder back chairs. Well, just one for now. If all works out well, I'll make more.

I will be at the point soon where I will need to steam bend the back chair posts and slats. I've seen the couple articles here in the articles section and I saw Ernie Connover's Shaker Rocker article in FWW from a couple years ago. He didn't go into detail on bending though.

I am thinking of using plastic pipe with a metal gas can. I'm not sure on fittings between the can and the pipe though and if/how to cap the pipe and so on.

I understand I need to get to a temp of about 212 and steam for about 2 hours.

This will be (obviously) new to me. Have you done this? Any suggestions one steam box ideas? Suggestions/tips in general?

Thanks!

Re: Steam bending chair posts - suggestions?

#2

Re: Steam bending chair posts - suggestions?

Chuck

>Have you thought of immersing the wood in very hot water? I have seen this method done as opposed to using actual steam.

Re: Steam bending chair posts - suggestions?

#3

Frank in Colorado Springs

Re: Steam bending chair posts - suggestions? *LINK*

Frank in Colorado Springs

>Some time ago I picked up a video by Lon Schleining entitled, "Steam Bending Basics". Email me if you're interested in purchasing my copy.


WC Article

Re: Steam bending chair posts - suggestions?

#4

Re: Steam bending chair posts - suggestions?

Mark Mandell - Gone Round In Jersey

>Joe,

You don't mention what flavor of wood you're using, and it does make a difference. Oak (red,black or white) and ash are fairly "easy" to work, sweet woods like cherry and maple take more effort.

A steam box is easy to make;I've made several. A double wall of 3/4" (giggle) exterior ply screwed together will do just fine and it's easy to make the length you need. Keep the inside dimensions 1-1/2" or so more than the stock you'll be working (the wood swells), but a smaller space is easier to heat up and hold. Set it on uneven legs so the condensate drains through a weep hole in one end. I've heard of people using Sch. 40 PVC pipe, but I think it tends to sag at steaming temperatures. I used 2 steam sources when over 30" in length. Make sure that your internal holders (to suspend the workpiece) will not react with your wood; I used 1/8" stainless steel rod stock or 3/8" pine doweling.

Yes, you need 212� to get the lignum softened enough to bend; soaking in hot water will not do anything for hardwood. Home bending anything over 1" will be a real adventure. "Cook" time for white oak is usually 1 hour per inch after the box reaches 212�

Hope this helps

Re: Steam bending chair posts - suggestions?

#5

That might work for really small things.

Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6

>But it would be pretty hard to come up with something to boil a couple of chair legs in.

You can save yourself a lot of work by finding some wood with that gradual bend grown in more easily than steaming.

You can make a steam chamber and boiler from almost anything. The rest is just plumbing in between.

Some pressure cookers have standard 1/4" NPT, pipe thread for the blow-out plug. This can be replaced with a flair fitting, and one of those crimped tubing lines like used behind space heaters to connect to the chamber. Pipe insulation will keep from loosing a lot of heat through it.

While you can use PVC with end caps for the chamber, I would consider making a plywood box with holes cut in the sides, where you only steam the part being bent, rather than the whole leg. While you are not likely to have any reverse bend outside of your planned bend, this take care of that potential problem, but it allows you to do more legs by cycling them through one at a time without having to open a chamber. You just pull one out, then insert another, or a plug as you run low.

If you are doing this outside in cold weather. I wrap chambers with several layers of packing foam to keep from loosing heat through the walls.

Also, I would have a length of aluminum foil ready to wrap around the bend area as quick is it comes out of the steam, until it is on the forum. This will stop evaporation and heat loss, giving you a little more time, which is in short supply when everything goes well, and means failure when unexpected glitches cause delay.

Here is a link to a free download book from Lee Valley. Everyone who plans to steam should get and read this several times before attempting it. While it sounds simple, there are many simple little things that will cause failure. Good luck

http://www.leevalley.com/wood/page.aspx?c=1&p=31161&cat=1,45866,45867&ap=1

Re: Steam bending chair posts - suggestions?

#6

Cherry

Joe in a Cleveland Suburb

>Thanks for the replies so far.

I am using scrap Cherry I had lying around.

Joe

Re: Steam bending chair posts - suggestions?

#7

Re: Cherry

Mark Mandell - Gone Round In Jersey

>I tried it. Was able to make the large bend for a chair back's "rungs", but could not make the sharper end bends for the tenons. Did some checking and found that the "tight" compound bends in cherry are most always done in factories using high pressure steam heated bending machines.

By all means take a shot, and post how you do.

Re: Steam bending chair posts - suggestions?

#8

Re: Steam bending for chairs

Glenn Madsen---in SF Bay Area

>I've taken three classes over the last year or so on Windsor chairmaking, and it's the steam bending that limits what I take on. Some woods bend nicely, some don't. Some designs are there for folks who can get the bending right. Other designs exist, but I have no idea how to make those work. Yet.

We found that green wood works best. Not kiln dried. And possibly not air dried, either. The sooner we got our sticks from the sawyer, the better.

Straight grain works better. Runout on sawn wood tends to be where the failures start.

And good heat helps. The double boiler described matches up with one of our better efforts. One of our guys is a retired engineer from the utility here. He built a large pressure pot, and got his walnut very flexible. That, matched up with a bending press one of the agricultural fellows had, gave us some fast bending for some of the more difficult parts. And it gave us some firewood, too.

Good luck with this. My project for this winter is a Shaker style rocker, likely in California Tan Oak.

Re: Steam bending chair posts - suggestions?

#9

JL

Re: Steam bending chair posts - suggestions?

JL

>I have one steam box (8' long) that I built out of exterior plywood. My older steam box (66" long) is S&D PVC.

My larger steam box rests on a large pot. My PVC steam box uses a old pressure cooker as steam source.

I usually steam green lumber. I have successfully steamed air dried walnut, cherry and other woods. You should have no problems with the moderate curvatures on cherry - but the pitch pockets may give you some trouble.

I would try and find an old pressure cooker. You can always find them at yard sales and flea markets. You don't really need one though. My larger steam box works quite well with just a pot.


img

Re: Steam bending chair posts - suggestions?

#10

Re: Steam bending chair posts - suggestions?

Philip Duffy

>I have put a setup together that consists of a new metal gas can as a water container, with a radiator hose leading to the steam box and a turkey fryer propane burner as a heat source. Mark has it all right; green wood and take time to make sure your bending form with posts and wedges are all positioned for easy reach. In a NY minute you need to get it all locked up on the bending form. Thin wood bends easily in 30 minutes. Allow an hour for one inch tick pieces. Have a spare handy, just in case the first one breaks when you bend it. Rived green wood should not break. Good luck and let us know how it worked out! Phil