Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Checker Board Table Top

Posts

Checker Board Table Top

#1

Checker Board Table Top

Tom Rex in TX

>I'm in the process of making a checkerboard game table for my son.

The squares for the top are going to be about 2 1/2" and 1/4" thick.

I am going to glue them to a 3/4" MDF board about 22" square.

I will put 3" edging around the squares and the MDF.

How would you make sure that each square is exactly the same size?

I've thought of getting them close to 2 1/2" on the table saw then gang clamping them on edge and running them through the planer then turning them 90 degrees and running them through on the other edge.

Your ideas would be greatly appreciated,

T Rex

Re: Checker Board Table Top

#2

Re: Checker Board Table Top

Barry Irby

>Tom, I don't think that will work and it might be dangerous. They would be too short to run through the planer. Any piece you run through has to be long enough for the feed rollers to hold them while the knives cut them. Smaller/shorter pieces tend to get caught in the knives and thrown around violently.

I would rip the strips with an excellent blade and glue them together in stripes. Then, square one end of the glued up board and with out changing the saw rip them into strips the other way, Creating rows of blocks. Flip every other one end for end and glue them back together in the checkerboard pattern. Much easier than trying to glue up individual blocks and a good excuse for buying a glue line combination blade if you don't have one.

If you have stock that is 2 1/2" square and long enough, you could plane two Identically sized blanks for light and dark. Then you could cross cut them into whatever thickness you wanted, creating end grain squares and then glue them up. You would have an end grain board and have to sand it flat and smooth.

Re: Checker Board Table Top

#3

Re: Checker Board Table Top

Tom Rex in TX

>Boy I sure didn't explain myself very well.

Let me try again.

My statement "I've thought of getting them close to 2 1/2" on the table saw then gang clamping them on edge and running them through the planer then turning them 90 degrees and running them through on the other edge."

After I cut them I would have 64 squares, 32 of each color.

I would place 8 of them side by side (call that a row) and 8 of these rows one behind the other (call that a column).

That way I would have a "board" 20 inches long (8 X 2 1/2").

On each side of the column I would clamp a �" board the same width as the squares (2 9/16) and run them through the planer on one edge.

Then I would unclamp and rotate the eight rows 90 degrees, clamp them again and run them through the planer again.

I would continue this process until I got them to 2 �".

I hope you can picture this.

Thanks again,

T Rex

Re: Checker Board Table Top

#4

Re: Checker Board Table Top

Dave Paine

>Barry mentions the easiest way to make the "blocks" by cutting strips of each wood, glueing the strips together and then cutting into strips of alternate wood.

One build on this is to cut 9 strips (5 of one species and 4 of the other), then you do not have to flip them, just move alternate strips one "block" to the side. This helps if the strips are not exactly the same thickness. Had this problem on my first chess board.

Re: Checker Board Table Top

#5

Re: Checker Board Table Top

Barry Irby

>Tom, I think I understand what you want to do, but I think you would have to glue the blocks to the carrier strip to make it work well. If you just sandwich the squares between two carrier strips, they will not be secure enough to plan the edges perfectly. They will vibrate and move and probably try to rotate and not come out square. You might be able to do what you want to do if you hot glue them or use double stick tape and clamp them securely, as long as you are planing the long grain edge of the blocks, but I don't think it will work when you rotate them and try to plane the end grain. If you had a drum sander like a Performax you might be able to do it.

I still think you are going to find it very difficult to plane pieces this small and end up with them square, uniform and with clean corners. Perhaps I'm stuck on my own method but I think you are over working this.

Re: Checker Board Table Top

#6

Gotta agree with Barry's method...

doug f, san clemente, ca

>Essentially you are making an end grain cutting board, just with bigger squares. If you cut pieces, then sand them to the same dimensions (cross sections) then crosscut the resulting glue up, you'll have your chess board. Sand the end grain and you're set to go.

I agree completely that cutting all the pieces first (2 1/2 by 2 1/2 x 2/1/2 blocks) THEN trying to plane them will not work well and could conceivable be dangerous.

Contrary opinions are always welcome.

Have fun with your project.

Doug

Re: Checker Board Table Top

#7

Sounds Like a Recipe for Disaster!

Dave (PacNW)

>I would not get any clamps or other metal objects anywhere near my planer. One small hick-up and BOOM an excuse to buy a new planer!

Just 4 Cents Worth (adjusted for inflation!)

Dave (PacNW)

Re: Checker Board Table Top

#8

Re: Sounds Like a Recipe for Disaster!

Barry Irby

>I agree with Dave, Never run clamps or anything metal through your planer. I had not even thought of it, and I hope you did not think I advised it. I was thinking of clamping the pieces together until the glue set. Even double stick tape benefits from a brief period of clamping. Apparently it takes a little time for the tape to develop its maximum "Grab".

So, do not run metal through your planer. I would not even run something through that had screws or nails even if I were "SURE" the knives wouldn't hit them. Planers have a habit of finding a way to chop into the metal and the results are never good.

This really is a table saw project. Rip the strips, glue them up, Cross cut them with the saw still set, and glue them again. I like the idea of adding an extra row and side slipping them rather than reversing them. (See, I knew I could change.)