Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

My Saw Stop just paid for itself

Posts

My Saw Stop just paid for itself

#1

My Saw Stop just paid for itself

Neal in San Jose

>Yep, I fired it tonight. Cutting the tops off of some boxes, even using a sled, when BAM! Actually not very loud when wearing hearing protection.

I couldn't figure out what I did wrong. Tried to recreate the moves I was making, and finally gave up after about 10 minutes thinking it must have been a mis-fire. As I was taking the fired break cartridge out, I noticed a teeny tiny drop of blood on the top of my right index finger. I wiped it off, and there is a very small cut in exactly the shape of the top of one tooth of my ATB 80 tooth blade. I didn't feel a thing, and as far as I can tell, it stopped before the next tooth got to me

I went back holding the sled with the cut in line with the blade, and it is obvious that a momentary lapse almost cost me a trip to the emergency room or worse. I feel now just like I did the first time I used anti-lock breaks for real! You will NEVER get me to let go of this thing.

Be careful out there - I know you are just like me trying to make a Dec. 25 deadline!!!!

(Still) 10 Fingers Neal

Re: My Saw Stop just paid for itself

#2

Wow, Glad it worked for you......

Barry Irby

>If I had the bucks I would buy one.

Don't know exactly what to say. Glad you weren't hurt any worse than that. Its good that you had the foresight to buy it.

Just to be contrary, is there any chance you were slack in your habits and relied on it to protect you? I doubt it. I would not have the nerve to rely on it.

Re: My Saw Stop just paid for itself

#3

Re: My Saw Stop just paid for itself

Jennifer@Indy.USA

>Great news Neal. I'm glad it worked as advertised!

Jen

Re: My Saw Stop just paid for itself

#4

Thanks for sharing

North of the Border

>Don't forget to get a replacement cartridge from SAWSTOP free of charge. This feature should be legislated to be a mandatory requirement for T/S like airbags for cars .... I know some people don't agree with that statement or still argue that it doesn't stop other safety issues like kickback, etc. Stopping smoking doesn't stop all cancers either. One thing at a time will get us safe woodworking.

Re: My Saw Stop just paid for itself

#5

I believe

North of the Border

>no woodworkers would let down their guard just because a safety net is there ... I never, for one, drive while thinking the airbags in my car will cushion me from injury.

Re: My Saw Stop just paid for itself

#6

Re: Thanks for sharing

john lucas

>You could make it mandatory and I could turn around and cut a finger off on the bandsaw, jointer, miter saw, or chainsaw. You have to pay attention when working with machines or sharp tools.

Although the table saw is an excellent idea and everyone who can afford one should buy one. My hat goes off to the inventors, great product. I think it's a wonderful idea. I just don't think it should be mandatory. I would have never been able to buy a table saw if they were all as expensive as that one. I would have missed out on a lot of the joys of woodworking.

What about rebuilding old machines. Some of us really enjoy making an old piece of iron work. Imagine trying to do that with all the electronics in that saw. When it dies and you can't get parts, it's history. Where back to the throw away society and too much of what we get now days is that way.

somewhere along the line we have to be responsible for ourselves. You can't put enough safety devices on everything to prevent all injuries.

Sorry, didn't mean to get on my soap box, it just ticks me off when people think you can legislate everything.

Re: My Saw Stop just paid for itself

#7

Re: I believe

Neal in San Jose

>No, I didn't let my guard down because I know there is a safety net any more than I drive differently now that I have anti-lock brakes in my new car. I was even using a sled to keep things under control. I just let a finger stray over to where it shouldn't have been. I wasn't even aware I had done it; thus the 10 minutes of trying to re-create the mistake, and I still didn't know what I had done wrong until the little speck of blood showed up. I have been making display stands for the Computer Electronics Show in Las Vegas next month and under a fierce deadline, and had been doing repetitious cuts for the last two days, and I just wasn't paying full attention.

I'll go to the dealer and pay full retail for a replacement brake tomorrow so I can get back on track. I'll send the spent cart. to Sawstop and see if they will send me a new one. Anyone interested in a "slightly used" 80 tooth ATB blade? It was working well in plywood...

Re: My Saw Stop just paid for itself

#8

karl jr

And i thought a brokem finger was bad.

karl jr

>I broke a finger by extending it beyond the tool into a natural edge bowl. Oops. Ouch. D*** thats gonna hurt! I bet you counted your lucky stars... and fingers

Re: My Saw Stop just paid for itself

#9

Re: Thanks for sharing

Dave Peebles Lyons, Ohio!

>North,

How about an email address and a real name. That would make your case a lot stronger for me. I may even agree with you, but I have never been a fan of someone making me do something.

I am so happy for you Neal. It worked just as it was designed. That is awesome!!

Best wishes,

Dave

Re: My Saw Stop just paid for itself

#10

Re: I believe

Barry Irby

>I know the danger of repetitive cuts. Not my strong suit. ADD boy here. Its very difficult for me to keep my mind on long repetitive jobs. Doubly bad if I am in a hurry or under a deadline. (One night I was impatiently waiting for the TS blade to spin down and stop. Apparently to speed things up, I reached out and was going to pinch the blade between my thumb and fore finger. Fortunately, I stopped and did not do it. When I realized how close that was, I turned and left the shop. Was not qualified to be in there at that moment.)

Glad it worked for you.

Re: My Saw Stop just paid for itself

#11

Just wondering . . .

steve mackay

>does it trash the blade ?

Re: My Saw Stop just paid for itself

#12

Re: Wow, Glad it worked for you......

Victor Parisian

>My son and I were just talking about the Saw Stop yesterday...

A couple of weeks back I nicked my thumb on the jointer. Turned out I had a blade that had worked loose and was about 1/32 higher on one end than the other. Scared me good. Have dead zone on the pad of my thumb to remind me to always always always use the push blocks etc.

Regards from Houston

Victor

Re: My Saw Stop just paid for itself

#13

Absolutely.

John E in SC

>From the videos I've seen, the saw blade is pretty much imbedded in the aluminum brake. Doubt you would even be able to get it out. There are videos on the Saw Stop website. Check 'em out. Pretty cool to watch.

Re: My Saw Stop just paid for itself

#14

Re: Just wondering . . .

Neal in San Jose

>Yep, my blade is pretty firmly stuck in the aluminum block. I'm sure I could wrassle it out, but I sure wouldn't trust it. If one of those carbide teeth is now a little loose, it could easily become a 100 mph bullet coming off the blade. Just not worth the risk.

Re: My Saw Stop just paid for itself

#15

Re: Thanks for sharing

Fred Davis

>Pining for the Government to ratchet up more regulation is probably a way of life North of the Border ;-))

FredD

Re: My Saw Stop just paid for itself

#16

Re: Thanks for sharing

Howard Norman

>>Pining for the Government to ratchet up more regulation is probably a way of life North of the Border<

It would seem that way Fred. That kind of society is not for me but if that what you like that is ones privilege I guess.

howard

Re: My Saw Stop just paid for itself

#17

Re: Just wondering . . .

Brian in Sandusky, OH

>I triggered my Sawstop once.

My fault. The metal miter gauge touched the blade.

Yes, it will completely ruin a blade.

I was able to remove the blade from the brake, and now it's on display on my wall as a reminder.

That's probably the only downside to SawStop, is that you are going to pay the cost of a blade and a cartridge with each fire.

But that is WELL worth it in my opinion.

Re: My Saw Stop just paid for itself

#18

If I'm not mistaken

North of the Border

>last time I read somewhere all new tablesaws (after 2011?) sold in the US must have the riving knife feature. I'm all for it, legislation or not, as long as it brings safety to the shop. By the way, when every machine has the SAW stop feature (I also heard that SAWstop is working or researching to put that feature into other machines), the price will go down a lot. Stability control systems, All wheel-drive , etc. will be standard features for many new models even though they cost a little bit more. If you want that model of cars, you can't say I want the cheaper (and less safe) version. SSC has been credited with saving lives juts like SAWSTOP saving fingers (and more). We all know for some matters (safety is one of them), legislation is a powerful and effective tool to move builders and makers towards better (if not) practices. This applies to almost all industries: oil & gas, hospitals, and whatnot. I'm not for legislation per se but when people say that legislation is a bad thing, I'd tell them to find out why they need their gov't (or Congress in the case of my friends south of the border).

Re: My Saw Stop just paid for itself

#19

My question about SawStop

Gary Evans--Tallassee TN

>Hi Neal,

Glad to see that you got out without significant damage. The only knowledge I have about SawStop is what I've read on this forum. I am wondering about the effect of the sudden stop on the arbor and it's bearings. Looks like the force of the blade hitting the brake would be transferred to the arbor with a twisting motion if nothing else. Of course, I guess the blade would probably slip some on the arbor when it stops.

Has anybody seen anything on this issue? Just curious. I'm among the group that would never buy a SawStop. No way I could afford it.

Gary

Re: My Saw Stop just paid for itself

#20

Questions

Barry Irby

>Does it fire if the saw is not running? Like if you use a square or sliding Tee bevel to set the blade? Do you have to unplug it or turn off the feature to change a blade? It might hurt you if it fired while changing a blade.

Re: My Saw Stop just paid for itself

#21

Nope

Neal in San Jose

>Won't fire if it isn't running. Also won't start if you are doing something stupid like touching the blade or if a metal ruler is against the blade.

Re: My Saw Stop just paid for itself

#22

Re: My question about SawStop

Neal in San Jose

>Gary: The saw is designed with that in mind. It doesn't hurt anything. Well, the brake cartridge and blade are toast of course, but the internals on this beast are massive - much heavier than the Jet cabinet saw I upgraded from. It wasn't even difficult gettng the fired cartridge and blade out; they thought that thru, too. A benefit of all that mass is that the thing just purrs - very little vibration, even with my dado blade.

Re: My Saw Stop just paid for itself

#23

Re: My question about SawStop

Mike Circo

>The Sawstop saws are specifically engineered to handle the stresses of the sudden stops. That is why there cannot be a retrofit kit for other saws, it must be designed and built to handle the blade brake.

I've been to demos where a rep would show the saw cutting wood just fine, then trigger the blade stop (with the infamous hot dog), then replace the cartridge and repeat the next hour. He did that all day with no negative impact to the saw.

In a nutshell, the Sawstop saws are designed to handle the energy of the brake. I'd get one in a flash if I were in the market for a new saw.

Re: My Saw Stop just paid for itself

#24

Re: My question about SawStop

xeddog

>Hmmm. Dado blades. I would guess that the SawStop will not work with dado blades? So if the SawStop manages to get into legislation, do you suppose Dado blades would become illegal like I hear they are in Europe?

xeddog

Re: My Saw Stop just paid for itself

#25

Again, Nope

Neal in San Jose

>It uses dado blades just fine. You have to change brake cartridges to the dado cartrige that they supply with the saw, a one minute exercise, and then change back when you are finished. I usually do dados with the router, always have, but tried it once just to see. No biggee