Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Epoxy clean up question

Posts

Epoxy clean up question

#1

Epoxy clean up question

Barry Irby

>I just assembles a box with dovetail corners with Epoxy from WoodCraft. It's one hour epoxy. I taped off the joints, but there is still some mess. When would you clean up and strip the tape? After an hour or two or would you wait over night?

(I used Epoxy because of the long open time. I had nine dovetails on each corner to glue up and was afraid I would be too slow for Titebond. Might have made it though.)

Re: Epoxy clean up question

#2

Re: Epoxy clean up question

Gil Jones...GA

>Hey, Barry, I don't know about the 1-hour epoxy, as I use the 5:1 West System Epoxy, and it takes a good 8-hours to set-up properly. I wipe up all the mess (on the wood, and on me) with lacquer thinner, or Denatured alcohol (but mostly with lacquer thinner).

Also, I have found that I can thin the West System epoxy with lacquer thinner or DNA to use for hardening punky areas of wood. It takes overnight to set-up when that thin, but does a good strengthening job on the punky / porous areas.

Gil

Re: Epoxy clean up question

#3

Re: Epoxy clean up question

Fred Davis

>Barry,

I use Titebond on wood joints exclusively and Dovetail joints need next to none if properly fitted.

if the joints are a press fit , a dab of glue in the bottom of the pin hole is all it takes.

FredD

Re: Epoxy clean up question

#4

Re: Epoxy clean up question

John Lucas

>I try to clean it up with acetone or alcohol shorty after assembly. If I don't get it done I wait until it's dry and carve it away. Carving isn't the best solution but sometimes it's all I can do when working around the clamps. I've always been leary of using too much solvent fearing that it would weep into the joint. I try to use a rag with just enough to get rid of the epoxy.

Re: Epoxy clean up question

#5

Bart Goldberg

Re: Epoxy clean up question

Bart Goldberg

>When the joint is loose fitting, then I think epoxy is a good choice since it is gap filling.

Just my 2 cents

Bart

Re: Epoxy clean up question

#6

Re: Epoxy clean up question

ThomD

>I wouldn't use epoxy for that, it tends to emphasize the glue line, along with the problems you have. I would probably use acetone for that, which is nasty. For cleaning tools, etc... orange hand cleaner, or vinegar is good. For skin Gougeon soap is my choice.

http://www.dixdesign.com/epoxsoap.htm

Re: Epoxy clean up question

#7

Re: Epoxy clean up question - thinning epoxy

ThomD

>There tends to be a view that thinning epoxy will allow it to sink into wood better and cure rot etc... problems. I'm no chemist, but I tried to chase this question down for a while. My overall impression is that the moolecular size, or something of the sort, is still too large. The thinned glue appears to be sinking in better, because the solvent is penetrating, but it is still mostly impossible to get anything greater than surface penetration. This is why the folks who make stuff like rot doctor get the big bucks.

Re: Epoxy clean up question

#8

Re: Epoxy clean up question

ThomD

>By the way...

One thing that can work is to dry assemble the joint, then hit it with watery crazy glue. Done right, this works very well. But it takes some experimentation to get your technique down.

The problem with non-water based glues, is that stuff like Hyde glue, and white glue actually shrink the sides of the joint together (generally your glues that will make a rubbed joint). Greasy glues like epoxy (sold for it's gap filling properties, solid performance up to 1/4" gap), or wetting glues like super glue will harden while the parts are held apart. The thing about CA/Super glue, is that it can also be used to hide cracks and make invisible joints by wicking, so if you know your way around it can be used.

Re: Epoxy clean up question

#9

Re: Epoxy clean up question

Fred Davis

>Well,

I wasn't going to go there Thom , but your right on about Ca , used right it performs miracles and also makes cleanup of Epoxy seem like a dream by comparison.

I have a Soldier friend presently in the shop who brought over some antique furniture for cleaning and repairing which his Luxembourg native wife brought with her after ther wedding in Paris.

He also is trying to make a small box with double dovetails of Maple and Walnut and had trouble with the small contrasting part chipping and breaking.

I had him get some thin CA glue and once he started the joint assembly to wick it into the joint.

That solved the problem.

FredD

Re: Epoxy clean up question

#10

Re: Epoxy clean up question

Richard Jones

>Barry,

Apple cider vinegar has worked well for a zillion or so rifle bedding jobs.

I like the smell as well..........

Rich