Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Best way to cut/scribe this

Posts

Best way to cut/scribe this

#1

Best way to cut/scribe this

DouginDenver

>My first try at loading a picture - hope it works. Copying an article in Fine Woodworking a few months ago I glued up wedges of ebony and holly to use as corner inlays in a sofa table. As you can see, the outside circumference does not end up a perfect quarter circle. I am wondering the best way to make it a perfect quarter circle of the correct radius. If I could scribe a line, I would use a spindle sander I guess. But how do I scribe a perfect line? Cant' really stick a compass point exactly on the point of the inlay - it's 3/16" thick. Can't really just use a round object like the quarter because it won't be the exact diameter and I could not exactly center the point in the circle. Ideas?


img

Re: Best way to cut/scribe this

#2

Re: Best way to cut/scribe this

Alan in Little Washington (NC)

>Draw what you want on paper and use contact cement to stick the paper to the veneered fan. Then carefully file and sand it to the lines.

Re: Best way to cut/scribe this

#3

Ellis Walentine

What I'd do

Ellis Walentine

>Take two small scraps of wood or thin plywood and drill a hole through both of them. Put a piece of double face tape on the top piece and reassemble your inlay on the tape, with the point of the inlay directly over the center of the hole. Then clamp the bottom piece to the table of your disk sander, install a pivot in the hole and use this to swing the outside radius of the inlay against the sandpaper. Presto.

Ellis


img

Re: Best way to cut/scribe this

#4

Lee Grindinger

transfer it from a pattern

Lee Grindinger

>Draw the shape you want of a piece of paper, cut it out with scissors, place it on your inlay and trace the pattern.

Re: Best way to cut/scribe this

#5

Steven Antonucci

I assume he needs four?

steve antonucci

>So I would do this "in the round" with a paper joint and just break the quarters at the end. A small pinhole on the underside would allow a pivot to do the whole thing.

Steve

Re: Best way to cut/scribe this

#6

Leave It To Lee Valley

charlie belden

>Lee Valley sells a set of brass circles with a pencil tip's hole in the middle. They come in a range of sizes. They're intended to pencil a line parallel to a surface the edge is rolling on.

No reason you couldn't line up the hole with the center of your inlay and draw a pencil line along the outside edge - assuming of course that one of the set has a radius you're after.

The sizes are

1/4

5/16

3/8

7/16

1/2

5/8

3/4

7/8

1

Set is of the first five sizes, the others can

be bought as well.

1/4 to 1/2" set pat no. 05N64.01

5/8" 05N64.05

3/4" 05N64.06

7/8" 05N64.07

1" 05N64.08


img

Re: Best way to cut/scribe this

#7

Thanks Ellis

DouginDenver

>This idea worked perfectly, except I used a spindle sander, and since it's radius to radius, accurate placement of the jig is not an issue.

Re: Best way to cut/scribe this

#8

Re: Best way to cut/scribe this

A Wright

>here is another possible alternative:

- Buy an appropriately sized plug cutter (Lee Valley has them to 3")

- Attach your piece to a piece of scrap wood with double stick tape

- Use a small bit in your drill press to allign the drill press with the center of your circle, and clamp the scrap wood down to the drill press table

- Put your plug cutter in the drill press and cut your quarter circle.