Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Drilling holes in front door for locks and knobs

Posts

Drilling holes in front door for locks and knobs

#1

Drilling holes in front door for locks and knobs

Terry Alexander

>As if I don't have enough to do to finish my own house.......

I will be going to Houston Friday to install a new front door in my brothers house. Shouldn't complain because family time is precious...especially as we get "less younger".

He ordered a custom door (urged by an interior designer). Nothing I can do about that. He did pay an extra $100 to have it pre-hung. (thank goodness).

That leaves me/us to tear out the old and install the new. I've done that several times.....no problem. BUT (isn't there always a "but" or a "yeah....but") I will have to drill the holes in the door for the doorknob and the deadbolt.

ANY advise from you guys (and gals) would be greatly appreciated. I have some hole saws and forsner bits, paddle bits, just about everything. But I think I remember on a DIY show one time that you really need some kind of special jig to drill on the edge.

Again....would appreciate any comments/suggestions before I leave early Friday a.m. Won't do me any good to have tools 500 miles away that I failed to bring.

As always....TIA

Terry Alexander in West Texas

Re: Drilling holes in front door for locks and knobs

#2

Re: Drilling holes in front door for locks and kno

Jerry Nicholson

>For the edge you probably need a 3/4 or 7/8 hole saw, depending on the lockset you are using. If you are really good (I am not!) you could eyeball it and drill straight in. I used a dowling jig to keep the drill aligned and drilled a 1/4 hole a bit deeper than the pilot on the hole saw would be going. This guided the hole saw right straight in.

Re: Drilling holes in front door for locks and knobs

#3

Re: Drilling holes in front door for locks and kno

A Wright

>Option 1 is to do it the "old school" way. There should be a paper template included with the lockset that you tape to the door and wrap around the side. Use a speed square as a reference and eyeball the hole to keep it straight. The key here is to be careful to keep your holes on the mark and the bits square to the door

Option 2 is to buy some sort of jig. The nice jigs (like the dewalt below) have bits built in. You clamp the jig to the door and attach your drill to the bits then bore through. This Dewalt one is $30 at Lowes, and they go up from there to get one maed of aluminum, with forstener bits instead of hole saws, etc. I have also seen less expensive jigs where you provide your own clamp and bits. If you go to a tool store and look around you will probably find a few versions


img

Re: Drilling holes in front door for locks and knobs

#4

Re: Drilling holes in front door for locks and kno

Jerry Nicholson

>I bought that Dewalt thing at Lowes and found it to be worse than nothing at all. I took it back after trying it on one door. It helps position the hole saws to start with but provides very little help in keeping the hole saw going in the right direction and I came very close to ruining the door.

It does look kind of impressive.

Jerry

Re: Drilling holes in front door for locks and knobs

#5

Ellis Walentine

Couple things

Ellis Walentine

>First, make sure your brother intends to use a regular doorknob set as opposed to a mortise lock. If he's thinking of a nice Baldwin mortise lock or something like it, your job is going to be a lot more complicated.

Next, assuming it is indeed just a regular entry door lock, you will need to know 1) the thickness of the door, 2) the diameters of the edge and face holes, and 3) the backset of the knob/handle center(most are 2 3/4" back from the edge of the door.

Once you know these things, you can take the appropriate hole saws or Forstner bits to do the drilling. Make a simple drilling jig to ensure an accurate pilot hole for your hole saw and your Forstner, and clamp it to the door on whatever center line is specified. You'll have to eyeball the centering of the Forstner shank in the guide hole once the body of the bit clears the jig, but with care that shouldn't be too difficult.

Don't forget chisels and drill drivers for mortising out the strike hardware.

Ellis Walentine, Host


img

Re: Drilling holes in front door for locks and knobs

#6

Re: Drilling holes in front door for locks and kno

Fred Davis

>Since this is "family" do nothing less then renting a lockset installation kit , preferably the one Kwikset has made for them.

Most hardware's and all tool rentals rent these kits out and once you familiarize yourself with it , the only thing to do carefully is measure the distance from the entry lock hole to the dead bolt hole assuming that will be what you have.

These kits use a forstner bit for the door lock and auger bit for the bolt hole in the door and jamb edge.

You will also need a 1/2" drill motor.

One thing I do with the kit I have is wax the inside of the hole for the door lock in the jig.

These jigs typically have a Aluminum insert that will seize a steel bit if the inserts have been dinged and most have.

Piece of cake Terry ;-))

FredD

Re: Drilling holes in front door for locks and knobs

#7

Re: Drilling holes in front door for locks and kno

Lewis Dodd

>Most locksets come with a template made as part of the instructions. These work but kinda suck. I bought one set at Home Depot when my daughter bought the locks and knobs, about $20.00 right beside the locks and I loved it. Well worth the $20.00, It used hole saws which were included. Ellis is right, nothing for the strikes are included. Make sure the hole saw template jig is the size of the knob and deadbolt. I really liked that little jig, especially for a "one man operation".

lewis

Re: Drilling holes in front door for locks and knobs

#8

Re: Couple things

Ken Romines

>Terry

You can make a jig before you leave home that works for a while. Use Ellis� image but use 2x material for both pieces and drill the holes using your drill press at home. Then put the pieces together and clamp to the door. Make sure your backspace on the knob location allows for the material thickness of the edge portion of the jig (DAMHIKT). If you use either a hole saw or a Forstner bit you can make this work.

Have fun.

Ken, from Lubbock

Re: Drilling holes in front door for locks and knobs

#9

Re: Drilling holes in front door for locks and kno

Barry Irby

>Good advice here.

First, as Ellis said be SURE you know what lock set he is using and what it requires. I installed one that had an 8" backset. I have also done the ones that required massive mortises.

I did a bunch of interior doors recently. Lowes has a Irwin set that is slightly better than nothing. (Maybe not). What I ended up doing was making my own, somewhat on the line of the one Ellis drew, but I made it two sided. Drilled holes through two pieces that matched the bore for the lock. Then drill a hole center in a piece that was the same thickness as the door. Attached the two pieces, one on each side with the holes lined up. Slip it on the edge of the door and clamp it securely with the center line of the holes at the height you want, usually about 36" off the floor. Then use it as a drill guide. I used hole saws and drill the lock bore from both sides.

I found the Irwin kit to be interesting, but flimsy. It was plastic and the guide rings were very easy to move around. The 1/4" pilot wandering around would move them.

By making a sturdy guide for both sides, you nearly eliminate the chance the entrance and exit holes will be out of alignment with each other. By drilling from both sides you eliminate the possibility of tear out.

The Irwin kit had a strange little "router" bit designed to cut the perimeter of the keeper strike plate. I found it to be worthless. I used a sharp knife to mark the mortise and a sharp chisel to cut it.

When I did about thirty doors I made a little router template for both the keeper and the strike plate. For one door I would do it with a chisel.

One thing you could do is Let your brother give you the make and model number of the lock set and you buy it and study it and make up your guides and templates before you go. Have him give you his credit card number for the purchase and then you could throw in a few essentials such as holesaws, a half inch right angle drive drill, a router, and some gasoline.