Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Help getting the right Epoxy?

Posts

Help getting the right Epoxy?

#1

Help getting the right Epoxy?

Barry Irby

>Like many of you I work sporadically in my shop and do a variety of projects. Sometimes I need a little epoxy, sometimes a lot ( a few ounces) and often none at all for a few months.

I have used the type that come in the twin syringes but it doesn't seem to be reliable. I tried the same brand in the bottles form the Borg, but it was difficult to measure and it seems to go bad on the shelf.

Obviously there are several questions here. How do you measure it accurately? How do you store it? Is there a general purpose one? Do you mix the fillers in it? What kind? Does it really fill joints? Where can I get a lesson?

So, is there a good sort of all 'round epoxy I can buy that will sit on the shelf and wait until I need some? Where do you buy it? Cost?

Re: Help getting the right Epoxy?

#2

Re: Help getting the right Epoxy? *LINK*

Joe in Tallahassee

>I've had good luck with West System epoxy. I use their # 105 resin and #207 hardener. Get the measured pump dispensers to easily measure out a little or a lot. I've had it on the shelf for years and it still seems to be good. Use it straight for a finish, thicken it a little for an adhesive, or thicken it a lot for a filler. I keep a supply of various wood sanding dust - from light to dark colored woods - to use as thickeners. West system also has good instructions and info at their web site.


West System Epoxy

Re: Help getting the right Epoxy?

#3

Re: Help getting the right Epoxy?

del schisler

>where i used to get mine from at a craft place or hobby shop I used to buy it in gal's yrs ago I poured the cypress clock's back in the 80's That was good stuff Some of the wood supplyers have it What they sell should be good Some of it will yellow tho

Re: Help getting the right Epoxy?

#4

Re: Help getting the right Epoxy?

Howard Norman

>I would second the use of the West System epoxy. Good stuff and their measuring pumps makes it easy to get the right amounts.

Re: Help getting the right Epoxy?

#5

Re: Help getting the right Epoxy?

DaleLenz

>Barry,

I use the 5-min. syringe type stuff from Devcon, I believe is company name. Have noticed, if you push the syringe plunger, off center it is possible to not get a 50/50 volume from both the resin and harden, takes longer to set up. For the record, I've had the Devcon epoxy 2-3 years, off the shelf, and it still works well. I use the expoxy mainly for filling wood defects, normally not for joint glue.

Re: Help getting the right Epoxy?

#6

Bart Goldberg

Re: Help getting the right Epoxy?

Bart Goldberg

>Barry,

1) I have never had 2 part epoxy go bad. Some times the resin will start to solidify in its container. This can be corrected by heating it up. Once fully liquefied, it will remain that was for quite a long time. I have never heard of 2 part epoxy going bad.

2) I use System 3 when I need to make a large batch. I have the measured pump and/or I use small measuring cups that are just for this purposes. West System is just as good.

3) For small/quick use, I use the LocTite 2 part 5 minute epoxy that comes in 2 separate squeeze bottles from the Borg. To measure, I just squeeze out two identical sized lines next to each other on a piece of scrap and mix. This is a 1 to 1 ratio epoxy. If you are not sure if you have the amounts even, then I would error on adding slight more hardener then resin. If you do not add enough hardener, the result will be rubbery.

Hope this answers your questions.

Regards

Bart

Re: Help getting the right Epoxy?

#7

Jesper, Denmark

Re: Help getting the right Epoxy?

Jesper, Denmark

>Ask yourself if you really need epoxy?

Weldwood is as good a glue for wood, and mixes easily with water. No need for fillers etc., but does have a dark brown glueline.

PU glues are also very good if you can accept the foaming up part.

Finally, regular wood glue of the garden variety are usually plenty strong, so unless you need the special properties of the epoxy.......

If you do go the epoxy way, buy a cheap kitchen scale and weight out the proportions. The density of the "resin" and "hardener" are usually quite close, so you can mix as little or as much as you like. The pumps are good if you use them, but they do leak down, so if not used for a while, you waste the first stroke of each.

Measuring 2:1 epoxies is much easier than the 5:1 stuff.

Re: Help getting the right Epoxy?

#8

Is this the Take Away?

Barry Irby

>Buy either the West System or System Three with the appropriate hardener and either the pumps or some accurate way to measure them. Also have the appropriate fillers available.

I am taking it that either of these would have a long shelf life if stored in a cool, dark, dry place.

Re: Help getting the right Epoxy?

#9

Re: Is this the Take Away?

Bruce, a MN Galoot

>I have some West System that is now 15 years old and still works. Cool, dry. Might change color, though, if it freezes.

Re: Help getting the right Epoxy?

#10

Re: Is this the Take Away?

Justin Szeliga

>The West System seems to be OK for a couple years, just needs to be warmed to about 70 degrees to flow OK

Re: Help getting the right Epoxy?

#11

Re: Is this the Take Away? *LINK*

Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6

>Barry, Epoxies don't have volatiles or moisture that need to evaporate to cure, so they keep better than most adhesives. I started with West, but hated the pumps when I needed more than a small amount. Those pumps can get slow, and, take in air, causing a little bubble blast which will throw off the ratio of whatever you have already pumped. That is very frustrating.

I switched to System 3, which I liked better, but then found FCI which is much cheaper by a lot than either of the above. You can buy the standard 1 - 1, which is very forgiving in its ratio.

I keep little 2 oz. solo cups to measure small amounts, and all sizes up to 16 oz. I find it a lot easier to just sit two cups side by side on the edge of the bench, then pour an equal amount in each, then mix them together.

Most projects, I don't bother pouring it into a roller tray, I just pour a small stream ahead of the roller while I am rolling out veneers and substrates etc.

I keep colloidal silica on hand to thicken it to whatever viscosity I feel that I need. I hardly ever use it straight. This is a very light powder. A 2 oz cup of it mixed into a 12 oz mix in a 16 oz cup will make it about as thick as latex paint. 4 oz will make it about like catsup, and 6 oz about like mayo, and 8 about like peanut-butter. You could use it that thick if you wanted to use a 3/8" tenon in a 1/2" mortise, and it would probably be as strong as any well fitted 3/8" T in a 3/8" M. Not that I am encouraging that.

Here is a link to my source. You can buy one resin, and use it with a huge selection of activators to get whatever properties you need, like storing strong acids or solvents to certain structural properties. The price is better, because they supply large industry, and don't advertise a lot like the first mentioned epoxies that most of us start out with.

You can but a two gallon kit of this for about what you would pay for a quart of the others.

As with any brand that you choose, I would suggest that you get their manual, and glean whatever you can from their information. That will keep you out of trouble, and open new paths of adventure.


http://www.fgci.com/

Re: Help getting the right Epoxy?

#12

Re: Is this the Take Away?

Craig D

>If you don't need very much, I got 9oz 30 minute epoxy for $10 at the local hobby store. I've used about 1 oz in the last year (mostly gluing wood into metal infill bodies, no fillers). OEM'd from Bob Smith Industries, it comes in twin squeeze bottle, is mixed 1-1 and I do that by eye on a piece of plastic (which I reuse). The only drawbacks I've noticed is it has to be cured above 70�, can't take heat (bond failed above 150-200F or so) and if you mix more than a little, the pot life starts to really shorten.