Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Curved Veneering

Posts

Curved Veneering

#1

Jack Guzman from Maine

Curved Veneering

Jack Guzman from Maine

>I've never done any veneering. I wish to attach a piece of storebought(Rockler)birdseye maple veneer to the curved top surface of a mantle clock.The body of the clock will be layers of 3/4" hardwood glued into a block ,laid on edge with the end grain on either side (right and left)and the curve cut out of the top edge.The curve that the veneer has to adhere to will be 180 degrees of a 5" circle with a return,opposite curve on both ends.Will grain orientation be an issue? What can I use for glue? I'm thinking of making a caul to the shape of the curve and use it with clamps to hold the veneer on til the glue dries. Does this sound practical? Any hints,don'ts,tips?

Direction to an online tutorial or magazine article might be helpful. I have several years of PW and FW.Thanks---Jack

Re: Curved Veneering

#2

Re: Curved Veneering

Ralph Lipeles

>If the veneer is flexible then I would use your approach with yellow carpenters glue. If the veneer is not too flexible I would first steam it and put it in the qual to establish the curve. After a day, remove it, use string or masking tape to correct for springback and let it dry for a few days. Then glue it in place with the cual.

Re: Curved Veneering

#3

Lee Grindinger

This might be...

Lee Grindinger

>This might be a good time to consider contact cement. I rarely suggest it but two things make me think it may be a good idea here.

First, since the veneer is store bought from Rockler I would imagine it's very, very thin..., perhaps even membrane backed so the thickness could by extremely thin. This leaves NO room for play in your caul, it would have to be nearly perfect since the slightest glue pocket or bubble would be sanded through in the prep for finish.

Secondly, since you have no experience with veneering this may not be a good time to learn trickier techniques like iron, hot hide or vacuum.

I'd suggest the simpler contact cement method, buy a high quality contact cement formulated for this use and practice it on a scrap, make sure your substrate is perfect before you apply the veneer, you'll have virtually no thickness for sanding.

Lee

Re: Curved Veneering

#4

Re: Curved Veneering

Jesse Cloud

>I agree with Lee. The problem with the caul is that it has to be a dead on exact match with the workpiece, or the glue-up will have wrinkles and bubbles. If this is a one-off project, contact cement might be the answer.

Best and easiest would be a vacuum press. Don't know where you are located, but if you ask here or at a local woodworker's club, I'll bet someone would be happy to run a glue up for you.

Grain orientation shouldn't matter. Go for what looks best.

Re: Curved Veneering

#5

Re: Curved Veneering

del schisler

>i have done some veneer What i would do if is going to be like a camel back clock Use the veneer not long way's The veneer will fold that is the way i would use it for the curve No steeming I would use contact glue They make glue just for contact which is thinner It never get's hard like glue will It set's up and holds Weldwood which i have used But it is to thick for what you are going to do. Any supplyer of verneer will have that glue Make the veneer flush with the edge and than the face you go over the flush edge and sand that way you don't see the end grain They also make a veneer saw which is very handy to have It has very fine teeth and cut's the veneer off with no breaking I have done lot's of clocks I used to import them and do the fixing up

Re: Curved Veneering

#6

Jack Guzman from Maine

Re: This might be...

Jack Guzman from Maine

>I'm going to try this. I have a big enough piece,I can experiment some. Thanks for the information.---Jack

Re: Curved Veneering

#7

Jack Guzman from Maine

Re: Curved Veneering

Jack Guzman from Maine

>I don't have access to a vacuum press.I was thinking of using a cork face on the caul.---jack

Re: Curved Veneering

#8

Jack Guzman from Maine

Camel Back Clock

Jack Guzman from Maine

>Thanks for that. I had never heard this style called by that name. It makes sense.---Jack

Re: Curved Veneering

#9

Ellis Walentine

Cork and cauls

Ellis Walentine

>Cork works for taking up slack in a caul setup like this. Don't forget to make the cork surface match the outside curve of the veneer. Consider making the caul sectional, with maybe five pieces -- one clamp on each. Personally I'd use yellow glue, because I think you can get uniform enough pressure if your cauls are fairly accurate.

Ellis