Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Looking for Good Lathe to Buy

Posts

Looking for Good Lathe to Buy

#1

Looking for Good Lathe to Buy

Bob S

>Hi, I have been wanting to purchase a lathe for several years, and am beginning my search. I will be using it to turn out beautiful maple bowls (ha ha, maybe someday!). I will be looking for a used unit, and would like some suggestions on what to look for. HP rating and other features to look for. Also, any particular brands or models to look for would be appreciated. I hope to score something for under $300.

Thanks in advance.

Bob

Re: Looking for Good Lathe to Buy

#2

JL

Re: Looking for Good Lathe to Buy *LINK*

JL

>Post over on the Turning Board.

IMO, you'd be better off taking a turning class or two. See which sort of lathe fits your bill. At that price range, you will be looking at a used mini lathe or a used Reeves or belt drive larger lathe. They all have their limitations. You can't turn long or big stuff on a mini and you can't reverse a belt drive very easily (along with some other problems).

Once you've had some turning under your belt, you can decide which lathe option to pursue.


WC Turning Board

Re: Looking for Good Lathe to Buy

#3

Re: Looking for Good Lathe to Buy

Randy Johnson

>As JL said, for that price, even used, you are probably going to be getting a small Jet, Delta, or something similar. If you do wind up getting bit, the small lathe won�t satisfy you for very long.

You post doesn�t indicate your location. If we knew where you live it could lead to an invitation to attend a nearby turning club meeting or possibly visit an individual shop. It could make a difference in your deciding on getting a small lathe now or wait a little while and getting a bigger one. If you are anywhere near me I would loan you my old Delta middie to give you the chance to find out if you like it. It�s underpowered (actually, I think that is a plus when you are starting out) and the swing is a little restrictive, but it has the ability to get you firmly hooked by the turning bug. Believe me, it does.

Re: Looking for Good Lathe to Buy

#4

Re: Looking for Good Lathe to Buy

del schisler

>I have the biggest delta lathe Don't remember the model You can put on any size motor you have Belt drive Also make sure the bed is flat and not a round type A few other things that has been covered Also buy good turning tools like Sorby ect Just get high end You won't regret it Not sears stuff Wont hold a good edge hate to run product down oh well

Re: Looking for Good Lathe to Buy

#5

Re: Looking for Good Lathe to Buy

Lewis Dodd

>Well, welcome to a real money investment process!

I bought a $300.00 Grizzly and outgrew it in about 15 days. I am now the proud owner of a Oneway 24X36 (about $5000.00 8 0r 10 years ago). I sold my Grizzly for $300.00.

You better have lots of money for EXTRAS!!! I have more accessories that cost me more than the lathe! Get some woodturning catalogs, like Packard Wood works or Craft Supplies. I agree with a previous poster, find a wood turning club in your area, wood turners are a different breed, never met a basd one! A lot of the members of these clubs are often trading up and have lathes for sale or know someone that does. It is definitely a whole new world.

Good luck and Happy turning!

Lewis

Re: Looking for Good Lathe to Buy

#6

Re: Looking for Good Lathe to Buy

Bob S

>Thanks for responses. I am in Massachusetts, south of boston. I haven't been able to find any 'training classes', other than a sold out one-day event in Boston for $350. Not for me, thats for sure.

I will keep looking, and will keep in touch, i think i may get bit!

Re: Looking for Good Lathe to Buy

#7

Re: Looking for Good Lathe to Buy

Lewis Dodd

>Bob, try www.woodturner.org and go from there, most woodturning clubs meet once a month and they will point you in the right direction.

Lewis

Re: Looking for Good Lathe to Buy

#8

Re: Looking for Good Lathe to Buy

Chuck Jurvelin

>Don't give up on looking for a good, used lathe. They are probably the most under-used machine in most shops. Every woodworker who goes to a woodturning exhibition leaves wanting to try his/her hand at turning. I agree with the statement about not buying low quality turning tools. Also, spend some time reading Fine Woodworking or other articles on sharpening. Without the correct edge on your tools, you will be very ineffective at turning. Another thing that was mentioned in the replys was having a reverse on your lathe. You can very easily add a reversing switch to most lathes- I have on mine and use it frequently when sanding/finishing on the lathe. Try placing a "wanted" ad in your local paper or on ebay or Craigslist. Good luck!

Re: Looking for Good Lathe to Buy

#9

Re: For a good used lathe, you need...

Glenn Madsen

>woodturners! So that search for a club, or a guild, gets you into that economy of the types that outgrow lathes.

Here's the thing: They are all enablers, looking to make new addicts for their habits. And they are all cheap, knowing that no one can afford all the geewhiz gadgetry that is offered for every one to buy. So they can really help get through the $2k barrier that seems to be there for starting turners, and get you turning, well, for cheap, before you clean out an IRA, and buy the latest fancy bowl lathe.

They're also a source of free to cheap green wood, a really good reason to turn.

And nice people, too.

Re: Looking for Good Lathe to Buy

#10

Re: Looking for Good Lathe to Buy *LINK*

Phil Joines Krum,Tx

>Here's a link to the American Assoc. of Woodturners chapter list. Enter your state in the search box.


AAW Mass chapters

Re: Looking for Good Lathe to Buy

#11

Still Having Fun With Mini/Midi After Three Years

charlie belden

>"If you do wind up getting bit, the small lathe won�t satisfy you for very long. "

I beg to differ. I've been using a JET mini/midi (10"swing, 14" between centers) for over three years - could be four - and haven't outgrown it. But then I have no desire to turn anthing larger than 10" diameter or over 14" long. And with a smaller lathe, I don't need tools with 16 to 20" long handles, or a captured hollowing system that takes up a lot of space. You can turn a hell of a lot of interesting things - other than large bowls - over and over and over again - on a mini/midi

Maybe just because they can, folks with BIG lathes tend to only do large to very large pieces - mainly bowls and platters - over and over and over again, ignoring all the other things you CAN turn, on a mini/midi or full sized lathe.

The lathe is just the beginnings of the cost of turning. Add a hundred or hundred and a half for a chuck, another hundred in jaw sets, a hundred or so for some basic turning tools, another hundred for a grinder, another hundred for a sharpening jig(S), . . .

Re: Looking for Good Lathe to Buy

#12

Re: Still Having Fun With Mini/Midi After Three Ye

Randy Johnson

>Okay, let me rephrase that.

Most people wind up getting a bigger lathe sooner or later.

I was bitten by the turning bug when I was given a natural edge bowl. Having, up to that point, zero interest in turning, I�d never seen one before. I went to the library, looked at a few how to books, and decided to give it a try. At the time, I had a Delta midi that was left over from my muzzleloading days when it was used to make powder horn plugs. I got a set of scaled down turning tools and went at it. Things have never been the same since.

It didn�t take me any time at all to want to try bigger projects than my lathe was capable of. I went into debt for a while to acquire a 3420B and I have never regretted it. I would say that half or maybe a little over half of the things I turn could be done just as well on your lathe. But sometimes I get a piece of wood that, due to grain pattern, demands to made into something beyond the capabilities of a smaller lathe. At those times I am really glad to have the one I have. Far from ignoring the things that be turned on smaller lathes, I have turned dollhouse scale bowls for both my mother and a few great nieces. As an aside, sycamore branches often have little knobs on them that make great dollhouse scale NE bowls.

The bottom line, is that anything you can do on a small lathe you can do on a big one. But you can�t turn a big bowl or a newel post on a midi. A lot of turners that start small probably keep their midi lathes just for small projects. Mine is sitting under a bench waiting for just the right person to come along. When they do I will give it to them. I want to spread the addiction around.

Re: Looking for Good Lathe to Buy

#13

Re: Looking for Good Lathe to Buy

Bob S

>Still Looking - Now Considering New - JET vs: Grizzly. Variable Speed crucial?

I have had no success on the used sites, for a quality lathe. Frustration is setting in. I may go for a mini/midi lathe and like my options from Grizzly. However, it appears JET has a better reputation but is approx. 25-35% more, for similar models. AND, shipping is even more.

Are JET products worth the extra$$, and can they be picked up locally anywhere in Massachusetts?

I was happy to see the thread had continued, when I looked today!

Re: Looking for Good Lathe to Buy

#14

Re: Looking for Good Lathe to Buy

Randy Johnson

>There is a Woodcraft in Boston that should have a selection of lathes to look at.

Also, many online vendors offer free shipping.

I have never seen a Grizzly lathe of any size but the general consensus seems to be that they are not up to par with some of Grizzly's other offerings. On the other hand, negative comments about any of the Jet lathes are rare. Variable speed is NICE. My powermatic has it and I doubt if I would buy a lathe that didn't have it. BUT, there have been a lot more things turned on lathes without variable speed than on lathes with it. It isn't a must have. It's just something you would really miss if you went from a lathe that had it to a lathe that didn't.

Re: Looking for Good Lathe to Buy

#15

Look on Craigs List *LINK*

John Cotten

>I am in KY and pulled up Mass. on craigs list and found several good starter lathes. I have included a link on a Rockwell Delta that should be a good lathe if it has been even reasonably well maintained.

Good hunting, and take your time. There will be good buy, just wait for them.


img

Delta Rockwell Wood Lathe $600.00

Re: Looking for Good Lathe to Buy

#16

"Good" lathe?

Bill Houghton, Sebastopol, CA

>That looks like the Delta heavy duty lathe, which has been on my lust list for years.

Re: Looking for Good Lathe to Buy

#17

Re: Looking for Good Lathe to Buy

Joseph Mulherin, Sr

>Bob, consider buying a used Shopsmith from Ebay or Craiglist.

Re: Looking for Good Lathe to Buy

#18

JL

Re: Looking for Good Lathe to Buy

JL

>I've had the Jet 1642 EVS for a number of years. Excellent lathe.

If you would have purchased it from a number of places after Thanksgiving, they were offering for 15% off.

Yes - variable speed is worth the money. I really like having variable speed. It is nice to be able to turn low and slow if necessary and really fast. The two models of the 1642 Jet are 1.5 hp (110 V) and 2 hp (220 V). Is the extra 0.5 hp worth it? It depends. Are you going to turn a lot of bowls? If so, consider a Powermatic 3520.

As an aside, keep checking the various online vendors. They may offer a free shipping deal. I picked up my band saw that way several years back.