Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Help! Poly over shellac

Posts

Help! Poly over shellac

#1

Help! Poly over shellac

Jake Dahn (SoMN)

>All,

I have a co-worker...let�s call him Dave; really it isn�t me.

Dave was asking some advice on topcoats for a pantry door he just fabricated. He told me he was going to coat it with shellac. I warned him about the dangers of shellac in a high use environment and its weakness when contacted by alcohols etc. I recommended using poly over the shellac as long as he uses de-waxed.

Here is the rub....he already shellaced the doors using zinsler NON-dewaxed shellac. Unfortunately, I concerned him with the appropriateness of shellac for a kitchen, and he wants to know if there is anything that can be done.

My finishing knowledge is limited and I searched the archives for this, but didn't find an answer.

Can non-dewaxed shellac be top coated with poly?

Thanks,

Jake D.

Re: Help! Poly over shellac

#2

Re: Help! Poly over shellac

Dave Paine

>This should work if the top coat is oil based. I have not used the Zinsner Shellac. I mixed up my own from flakes and alcohol.

I have only tried this a few times. I applied the Shellac which was very effective in highlighting some glistening grain patterns in the wood - a mahongany species.

I waited a day or so, then applied Oil based polyurethane. This is important. Water based would likely not work.

In my projects the end result looked terrific, and I got a water resistant top coat.

Re: Help! Poly over shellac

#3

Easy Fix. *LINK*

Mark Mandell - Gone Round In Jersey

>[Especially if "Dave" has a sprayer]

Step 1. An alcohol bath rubdown using denaturel alcohol and a maroon (fine or very fine) synthetic wool pad. No smoking and do this outside.

Step 2. When he's got as much (maybe not all is ok)of the old orange shellac off, let dry that recoat with Zinnser's SealCoat which is a 100% dewaxed shellac.

Step 3. After drying for at least 3 days to allow all of the alcohol to evaporate, top coat with either oil and waterborne poly.

Suggestion: Quality waterborne poly will do very well in this application, but not the junk they sell in the BORGs. Gop to Homestead at the link and pick up either the General Finishes Super Poly, the Enduro Cl;;ear, or Target's Emtec 9000. These are best applied with an HVLP units, but can be hand-applied with a good synthetic brush. DO NOT, however US A SPONGE BRUSH with waterborne finishes as they entrap air that will bubble or leave pits in the surface.


HomeStead - Jeff Jewitt

Re: Help! Poly over shellac

#4

Thanks

Jake D (SoMN)

>Thanks much for the replies.....I didn't want to give bad advice.

Jake

Re: Help! Poly over shellac

#5

Re: Thanks

Kelly Anderson

>I would think that one or two coats of Zissners de waxed shellac over the waxed would solve the problem.

Re: Help! Poly over shellac

#6

Re: Problem

Mark Mandell - Gone Round In Jersey

>Kelly,

Since any additional application of shellac will partially dissolve the first application, you'll have some migration of the wax content to the top layer leading to adhesion issues. "Rinsing" off most of the first stuff is the better course to prevent problems.

Special Note here that when waterborne top coats are used, heavy shellac under-layers (especially with product that is not fresh-mixed) have a tendency to cold check creating cracks in the finish. I learned this the hard way and consulted with Jeff Weiss, the owner of Target Coatings.

Re: Help! Poly over shellac

#7

The easiest solution is to......

Howard Acheson

>... use a non-poly varnish. Pratt & Lambert #38, Sherwin Williams Varnish, Cabot #8000 varnish, Waterlox Original and Behlen Rockhard are all excellent non-poly varnishes. They will also produce a much nicer and clearer finish than a poly varnish.

Re: Help! Poly over shellac

#8

Re: The easiest solution is to......

Fred Davis

>far and away the easiest and best looking finish for your project

FredD